AGI Westeel EasyFlow2 100 Series Скачать руководство пользователя | Manualshive

Страница: 30 / 74

background image

30

BU-0101704 R3

Position the Underfloor Auger on the Bin Floor

Lift the underfloor auger and place it on the bin floor. Use proper lifting equipment (see

Section 5.4 – Required

Lifting Equipment on page 24

).

Note

The bin unload does not need to be located at the center point of the bin at this stage of assembly.

Remove the Lower Gearbox Controls

Remove the lower gearbox controls to allow for the underfloor auger to clear the bin wall cutout and to enable
the bin adapter to slide over the lower gearbox control rod.

1. Remove the 1/4” x 1-1/2” bolts (1) and nylon locknuts (2) from the coupler (3) of the lower gearbox control

rod (see

Figure 11.

Unfasten the Coupler from the Gearbox Control Rod

2. Remove the 7/16” x 1–1/4” bolt (5), locknut (6), and bushing (7). Remove the gearbox shift lever (8) from

the underfloor auger (see

).

2

3

1

4

2

3

1

4

EASYFLOW2 (100 SERIES) – FARM TUBE BIN UNLOAD SYSTEM

«
...
28
29
30
31
32
...
»

Содержание Westeel EasyFlow2 100 Series











































































Отзывы:

Нет отзывов

Похожие инструкции для Westeel EasyFlow2 100 Series

SACE Tmax XT Series

Бренд: ABB Страницы: 11

4 Happy Kids GUCIO

Бренд: 4iQ Страницы: 12

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

Бренд: YATEK Страницы: 72

Бренд: Bacharach Страницы: 48

Бренд: Keller Страницы: 12

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 4

Бренд: M-system Страницы: 5

Бренд: MA Страницы: 2

Бренд: Panasonic Страницы: 23

TechPRO VCI1000

Бренд: MAHLE Страницы: 2

Бренд: Eternal Lighting Страницы: 10

Бренд: Henny Penny Страницы: 26

Towman's Liberty Series

Бренд: Whelen Engineering Company Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды