AGI Westeel EasyFlow2 100 Series Скачать руководство пользователя | Manualshive

Страница: 6 / 74

background image

6

BU-0101704 R3

2. Safety

2.1. Safety Alert Symbol and Signal Words

This safety alert symbol indicates important safety messages in this manual. When you see
this symbol, be alert to the possibility of injury or death, carefully read the message that
follows, and inform others.

Signal Words:

Note the use of the signal words

DANGER

,

WARNING

,

CAUTION

, and

NOTICE

with the safety

messages. The appropriate signal word for each message has been selected using the definitions below as a
guideline.

Indicates an imminently hazardous situation that, if not avoided, will result in serious injury or
death.
Indicates a hazardous situation that, if not avoided, could result in serious injury or death.

Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury.

Indicates a potentially hazardous situation that, if not avoided, may result in property damage.

2.2. Follow Safety Instructions

Read and understand all safety instructions, safety decals, and manuals and follow them when operating or
maintaining the equipment.

• Owners must give instructions and review the information initially and annually with

all personnel before allowing them in the work area. Untrained users/operators
expose themselves and bystanders to possible serious injury or death.

• Use for intended purposes only.

• Do not modify the bin unload in any way without written permission from the manufacturer and is not

covered by the warranty.

• Follow a health and safety program for your worksite. Contact your local occupational health and safety

organization for information.

• Follow applicable local codes and regulations.

EASYFLOW2 (100 SERIES) – FARM TUBE BIN UNLOAD SYSTEM

«
...
4
5
6
7
8
...
»

Содержание Westeel EasyFlow2 100 Series











































































Отзывы:

Нет отзывов

Похожие инструкции для Westeel EasyFlow2 100 Series

Бренд: Raymarine Страницы: 464

Бренд: 3M Страницы: 8

Бренд: ZOLL Страницы: 3

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: Baileigh Industrial Страницы: 40

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: Ecler Страницы: 108

Бренд: R&S Страницы: 121

Бренд: NEILPRYDE Страницы: 55

Бренд: HANYOUNGNUX Страницы: 4

Бренд: Park House Healthcare Страницы: 6

Бренд: J&M Страницы: 33

Бренд: Tascam Страницы: 8

Бренд: Rainbow Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды