AGI 15100SA Скачать руководство пользователя страница 35

Страница: 35 / 82

P1512161 R0

5. Pull the upper front frame down until the bottom of the cloth touches the front flashing, and hold it in place

with a bungee cord around the front frame of the hopper weldment (see

Note

The length of the upper side frames provides leverage to pull the upper front frame down against
the opposing torque of the springs.

Figure 25.

Holding Upper Frame with Bungee Cord

6. Attach the hopper cloth to the conveyor (see

Figure 26

•

First, attach the front of the hopper cloth to the front flashing. Afterward, attach the sides.

•

Drill through the hopper cloth and use the existing holes as a guide through the lower frames, flashings,
and hopper weldment.

•

Fasten using 1/4" x 1-1/4" elevator bolts (5) and 1/4" nuts (6).

SWING AWAY CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

3. ASSEMBLY

Содержание 15100SA



















































































Результаты поиска

Содержание 15100SA

Отзывы:

Похожие инструкции для 15100SA

Бренды по названию

Популярные бренды

AGI 15100SA, Инструкция по сборке

Результаты поиска

Содержание 15100SA

Отзывы:

Похожие инструкции для 15100SA

Бренды по названию

Популярные бренды