AGI 15100SA Скачать руководство пользователя страница 9

Страница: 9 / 82

P1512161 R0

1.6. Tire Safety

Failure to follow proper procedures when mounting a tire on a
wheel or rim can produce an explosion that may result in
serious injury or death.

• DO NOT attempt to mount a tire unless you have the proper

equipment and experience to do the job.

• Have a qualified tire dealer or repair service perform

required tire maintenance.

• When replacing worn tires, make sure they meet the original

tire specifications. Never undersize the replacement tire.

• DO NOT weld to the tire rim with the tire mounted on the

rim. This action may cause an explosion which could result in
serious injury or death.

• Inflate tires to the manufacturer’s recommended pressure.

• Tires should not be operated at speeds higher than their

rated speed.

• Keep wheel lug nuts tightened to manufacturer’s

recommendations.

• Never reinflate a tire that has been run flat or seriously

under-inflated without removing the tire from the wheel.
Have the tire and wheel closely inspected for damage before
remounting.

SWING AWAY CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

1. SAFETY

Содержание 15100SA



















































































Результаты поиска

Содержание 15100SA

Отзывы:

Похожие инструкции для 15100SA

Бренды по названию

Популярные бренды

AGI 15100SA, Инструкция по сборке

Результаты поиска

Содержание 15100SA

Отзывы:

Похожие инструкции для 15100SA

Бренды по названию

Популярные бренды