AGI 15100SA Скачать руководство пользователя страница 37

Страница: 37 / 82

P1512161 R0

Figure 27.

Installing the Handle

Install the Cable and Clamps

1. Point the hopper handle toward the hopper (see

Figure 28

2. Secure the cable (1) to the handle with a cable clamp (2).

3. Route the cable through the cable rung (3) and around the cable sheaves.

4. Attach a 7/8" cable clamp (4) to the front upper frame using one 5/16" x 1" bolt (5), one 5/16" nut (6) and

two 5/16" flat washers (7). See

Figure 29 on page 38

5. Loop the cable (1) around the 5/16" x 1" bolt (5) and secure with 1/4" cable clamp (2).

6. Test the function of the collapsible hopper cloth controls by raising and lowering the handle. Adjust cable

tension as required.

Table 10.

Cable and Clamp Components

Item

Description

1/8" Cable 13' [4.0 m]

1/4" Cable Clamp

Cable Rung

7/8" Cable Clamp

5/16" x 1" Bolt Gr8 Plated

5/16" Nylon Locknut Gr8

5/16" Flat Washer Plated USS

SWING AWAY CONVEYOR – PORTABLE GRAIN BELT CONVEYOR

3. ASSEMBLY

Содержание 15100SA



















































































Результаты поиска

Содержание 15100SA

Отзывы:

Похожие инструкции для 15100SA

Бренды по названию

Популярные бренды

AGI 15100SA, Инструкция по сборке

Результаты поиска

Содержание 15100SA

Отзывы:

Похожие инструкции для 15100SA

Бренды по названию

Популярные бренды