AGCO HayBoss G2 445, HayBoss G2 450 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 44

background image

20

5. Power Cable and Main Wiring Harness Installation

1. Locate the power harness.
2. Connect the power harness (006-4640A) to the battery (12 volt) using the red wire with fuse to the

positive side and the black wire to the negative.

A. The power harness must be connected to the battery!

The unit will draw more amps than

convenience outlets can handle. Any modifications of the power harness will void systems
warranty.

CONTACT HARVEST TEC IF MODIFICATION IS REQUIRED!

B. This unit will not function on positive ground tractors.
C. If the unit loses power while operating it will not keep track of accumulated pounds of

product used.

3. The power harness (006-4640A) will run from the tractor battery to the hitch. The power harness (006-

4660K) will connect to the tractor power harness (006-4640A) at the hitch. Run the Communication
harness (006-4660N) from the cab to the hitch. This wire will connect to the Communication harness
(006-4660KE). These wires will run together to the Baler Mounted Processor (006-4671SS).

4.  Connect Flow Meter (006-4725A) to the Baler Mounted Processor.
5.  Connect Pump Harness (006-4660Z) the Baler Mounted Processor.
6.  If you have the optional Hay Indicator connect it to the Baler Mounted Processor.
7.  Attach moisture cable (006-4640K) to Baler Mounted Processor.
8.  Connect bale rate sensors cable (006-7202) to the extension harness (006-7400EXT) and then to the

Baler Mounted Processor.

9.

Install Baler Mounted Processor in pump plate using 5/16” lock, nut and flat washers.

NOTE: The plugs on the Baler Mounted Processor must face down. Failure to mount
correctly will void systems warranty.

System Wiring Diagram

462 Terminal

006-4670

Pump Harness

006-4660Z

Comm Terminal

to Hitch

006-4660N

Comm Hitch to Baler

006-4660L

Bale Rate Sensors

006-7202 & 006-7400EXT

Tractor to Hitch

Power Cable

006-4640A

Hitch to Baler Power Cable

006-4660K

Moisture Cable

006-4640K

Optional
Hay

Indicator

Flow Meter
006-4725A

Baler
Mounted
Processor
006-4671SS

«
...
18
19
20
21
22
...
»

Содержание HayBoss G2 445, HayBoss G2 450













































Отзывы:

Нет отзывов

Похожие инструкции для HayBoss G2 445, HayBoss G2 450

Бренд: NEC Страницы: 29

Бренд: Xebex Fitness Страницы: 15

Бренд: qeedo Страницы: 2

Бренд: Federal Signal Corporation Страницы: 12

Бренд: laerdal Страницы: 9

HQ Power VDL25BM

Бренд: Velleman Страницы: 3

Бренд: iGuzzini Страницы: 36

AQUIS ULTRAFLOW

Бренд: Waterous Страницы: 56

Бренд: H&S Страницы: 54

Бренд: Samson Страницы: 2

Retractable Box Scrapers HR3584

Бренд: Land Pride Страницы: 1

Бренд: Hedson Страницы: 32

Бренд: JLG Страницы: 165

Бренд: Labconco Страницы: 174

Бренд: GSWeb Playground Equipment Страницы: 20

SonicShield I Micro

Бренд: CMS Marine Страницы: 15

Бренд: Dean Страницы: 2

Бренд: HunterLab Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды