AGA legacy 110 Dual Fuel Range, Руководство пользователя и инструкции по установке

Страница: 35 / 40

35
WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
18. To Adjust Oven Door Catch Keep
Open oven door, slacken off locknut at base of keep,
and screw in or out as required until required fit is
obtained. Retighten locking nut.
19. To Change Ignition Generator
Disconnect from electricity supply.
Pull cooker forward to gain access to the cover box at
the rear of the cooker. Remove the screws securing
the cover and lift clear. Pull off all the leads to the
generator noting their positions. Slacken the two
screws holding generator to cooker and remove
generator.
Fit new generator to cooker and replace leads.
Reassemble in reverse order. Refer to wiring
diagram. Check ignition performance.
20. To Remove RH Oven Inner Back.
Open RH oven door and remove 4 screws and
washers securing the inner back to the back of the
oven. Carefully lift away the inner back. Reassemble
in reverse order making sure that the 4 screws and
washers are fully tightened.
21. To Change Fan in RH Oven.
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear.
Remove 4 screws securing the electric cover to the
back sheet and remove cover. Disconnect the 3
terminals connected to the fan noting their position.
Remove oven inner back (see 20). Hold the fan blade
and remove the centre nut (left hand thread) 2 brass
washers, fan blade and circlip. Unscrew fan retaining
nuts and washers (3 off each) and lift the fan away
from the rear of the cooker. Fit new fan and
reassemble in reverse order. Check operation of
oven.
22. To Remove RH Oven Element.
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear.
Remove 4 screws securing the electric cover to the
back sheet and remove cover. Disconnect the 3
terminals connected to the element noting their
position. Remove oven inner back (see 20). Remove
2 screws from the top of the element and 1 from the
bottom of the element in side the oven. Lift out
carefully, refit new element, reassemble in reverse
order. Check operation of oven.
23. To Remove Grill Element.
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear.
Remove 4 screws securing the electric cover to the
back sheet and remove cover. Remove the 4
terminals connected to the elements noting their
position. Remove grill pan from grill chamber. From
inside grill compartment remove enamelled front
shield from grill roof, 2 screws and washers. Remove
2 screws and washers securing the grill element front
support. Remove 1 screw from each of the grill
elements and withdraw grill elements from grill
chamber. Fit new elements, reassemble in reverse
order. Check operation of grill.
24. To Remove LH Oven Elements.
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear. Remove
4 screws securing the electric cover to the back sheet
and remove cover. Remove the 4 terminals connected
to the top element noting their position. Remove 2
screws and washers securing the bottom element
cover. Remove the 2 terminals connected to the bottom
element noting their position. Remove 2 screws and
washer from the bottom element support. Remove 2
screws and washer from the element bracket and
withdraw the element. Fit new element, reassemble in
reverse order. Open LH oven door and remove 2
screws and washers securing the top element heat
shield. Remove 2 screws and washers from the top
element bracket and withdraw. Fit new element,
reassemble in reverse order. Check operation of oven.
25. To Change Warmer Neon
Remove RH hotplate (see 2). Carefully place hotplate
upside down on a suitable flat surface. Remove 2
screws holding neon bracket to Warmer frame. Fit new
neon and bracket assembly.
Reassemble in reverse order and check for correct
operation.
26. To Change Warmer
Disconnect from electricity supply.
Pull the cooker forward to gain access to the rear.
Remove RH hotplate, see 2. Fit the new hotplate and
reassemble in reverse order.
Warmer operation is satisfactory.
27. To change oven light bulb.
LH Oven
Remove the oven furniture and side linings. Remove
the oven rear liner (3 screws)
RH Oven
Remove the oven inner back (see 22). The oven
light cover is now accessible. Unscrew the cover.
Unscrew the bulb.
Fit an Edison screw fitting 15w 240v lamp, FOR
OVENS. It must be a special bulb, heat resistant to
300°C.