AETOOL BESA-12P Скачать руководство пользователя страница 46

Страница: 46 / 56

BESA-12P User’s manual

46 -

www.aetool.com

AETOOL LTD.

Page 23

10. If either minimum or maximum charging volts are not within the voltage

range limits then it will display one of the screen as below (Figures 72 & 73)
and it will prompt you to check the alternator system for the fault.

11. To exit the program, pressing the

key at any moment will exit and

return back to the main menu screen (Fig.62).

12.0

–

View Last Test Results

To view the results of the last test, BESA-12P has to be connected to an external
power source by either clamping its clips directly to a 12 Volt car battery or
connected to a PC via the USB port.

1. Once power up, the wakeup screen will display as follows:

Figure 72

Figure 73

Figure 74

Results: Low charge

At 2,000 rpm,
Loading Test:
>13.5V: Max. 13.3V

Check for loose belt and
the alternator.

Results: Low charge

At 2,000 rpm,
Loading Test:
>12.5V: Min. 12.4V

Check for loose belt and
the alternator.

USB Cable

BESA- 12P

Содержание BESA-12P

























































Результаты поиска

Содержание BESA-12P

Отзывы:

Бренды по названию

Популярные бренды

AETOOL BESA-12P, Руководство пользователя

Результаты поиска

Содержание BESA-12P

Отзывы:

Бренды по названию

Популярные бренды