AeroWorks 30cc EXTRA 300 ARF-QB Скачать руководство пользователя страница 67

Страница: 67 / 101

Fuel Tank Assembly

1. Gather the fuel tank parts as shown below.

◊

1 - 15oz fuel tank

◊

1 - Fuel tank stopper

◊

2 - Aluminum stopper mounts with screw

◊

1 - Fuel clunk- Large

◊

3 - Brass tubing- Large

◊

2 - Fuel barbs

◊

3’ - Large fuel tubing

(Not Supplied)

◊

1 - Aeroworks fuel “T”

(Not Supplied)

FUEL TANK ASSEMBLY AND INSTALLATION FOR GAS ENGINE

2. Locate the (2) supplied brass fuel barbs. Solder a

brass fuel barb to the fuel line pick up tube. This
will keep the weight of the fuel clunk from pull-
ing the fuel line off the brass tube.

Note:

No brass barbs are required for the air vent

lines.

3. Assemble the fuel pick up line, rubber stopper

and metal end caps. As shown below.

Note:

Supplied rubber stopper can be used for glow

or gas fuels.

4. Solder a brass fuel barb to the other end of the

fuel pick up line.

Содержание 30cc EXTRA 300 ARF-QB






































































































Результаты поиска

Содержание 30cc EXTRA 300 ARF-QB

Отзывы:

Бренды по названию

Популярные бренды

AeroWorks 30cc EXTRA 300 ARF-QB, Инструкция по сборке

Результаты поиска

Содержание 30cc EXTRA 300 ARF-QB

Отзывы:

Бренды по названию

Популярные бренды