AeroWorks 30cc EXTRA 300 ARF-QB Скачать руководство пользователя страница 37

Страница: 37 / 101

MAIN LANDING GEAR

AND WHEEL PANT ASSEMBLY

2. Align mounting holes of main landing gear with

pre drilled mounting holes in fuselage mounting
plate.

Note:

Mounting holes have been offset to ensure

proper installation of main gear.

3. Assemble the landing gear bolts with lock

washer and flat washer. Use a drop of blue Loc-
tite on landing gear bolts before attaching the
landing gear.

4. Bolt landing gear strut to fuse with (4) 6-32 bolts

and washers.

Mounting holes

have been offset

to ensure correct

installation

Main Landing Gear Installation

Gather the landing gear parts as shown below.

◊

1 - Carbon landing gear strut

◊

2 - 2 1/2” Foam Tires

◊

2 - Axles with lock nuts

◊

4 - Wheel collars

◊

4 - 6-32 mounting bolts

◊

4 - 6-32 Lock washers

◊

4 - 6-32 Flat washers

◊

2 - Wheel pants

◊

4 - 4-40 Bolts

◊

4 - 4-40 Washers

5. Using lock nut install axle to gear.

Note:

Do not tighten securely yet.

Содержание 30cc EXTRA 300 ARF-QB






































































































Результаты поиска

Содержание 30cc EXTRA 300 ARF-QB

Отзывы:

Бренды по названию

Популярные бренды

AeroWorks 30cc EXTRA 300 ARF-QB, Инструкция по сборке

Результаты поиска

Содержание 30cc EXTRA 300 ARF-QB

Отзывы:

Бренды по названию

Популярные бренды