background image

15

Problem

Possible Cause

Solution

RED TROUBLE 

Indicator is blinking 

rapidly

Utility fault

1.  Power cycle charger at breaker 

box. 

2.  If the condition persists, have 

a qualified electrician inspect 

the wall outlet ground circuit 

integrity.

3.  Repair as required.

Above temperature 

limit Cases:
•  Temperature 

is too high. 

The charger 

will restart 

charging when 

it cools down.

4.  Inspect charger module for 

overheating (hot to the touch).

a.  Carefully unplug vehicle 

coupler and allow to cool.

b.  If the condition persists, 

contact Customer Service for 

assistance.

5.  Remove power to the Wallbox 

at the circuit breaker. 

6.  Have a qualified electrician 

inspect the installation.

a.  Repair as required. 

RED TROUBLE 

Indicator is on solid 

when connected to 

vehicle

RED TROUBLE 

Indicator is off 

and BLUE STATUS 

Indicator is on when 

you unplug from 

vehicle

Vehicle problem

Contact Customer Service.

 

RED TROUBLE 

Indicator is on solid 

NOT connected to 

vehicle

Charger internal 

failure

Contact Customer Service for as-

sistance.

RED TROUBLE 

Indicator and BLUE  

STATUS Indicator 

are flashing red and 

white.

Charger trying to 

resolve internal 

error

Charger will return to normal opera-

tion within 1 minute. If problem 

persists, contact Customer Service 

for assistance.

Содержание TurboDX EVSE-DX

























Отзывы: