Aeropro LT50 Скачать руководство пользователя страница 8

Air Finish nailer LT50             

        Http://www.aeroprotools.com 

 

5. Maintenance 

Disconnect  the  tool  from  the  compressor  before  adjusting,  clearing  jams,  servicing  &maintenance, 

relocating and during non operation.   

      Regular  lubrication,  if  your  tool  without  using  the  in-liner  automatic  oilier,  place  2  or  6  drops  of 

pneumatic tool oil into the air inlet before each work day or after 2 hours of continuous use depending in 

the characteristic of work piece or type of fasteners.   

      Air-operated tools must be inspected periodically, and worn or broken parts must be replaced to keep 

the  tool  operating  safely  and  efficiently.  Check  and  change  all  worn  or  damaged  O-ring,  Seals,  etc. 

Tighten all the screws and caps to avoid personal injury. This should be done by an expert. 

      Make regular  inspection for free movement of trigger,  spring  and safety mechanism to assure safe 

system is complete and functional: no loose and missing parts, no building or stocking parts. 

      Keep magazine and nose of tool clean and free of any dirt lint or abrasive particles. 

      When temperatures are below freezing, tools should be kept warm by any convenient, safe method.                                                                                                                                                                                                                                                     

6. Troubleshooting 

(See Table 1) 

SYMPTOM 

PROBLEM 

SOLUTIONS 

Air  leak  near  top  of  tool  or 

in trigger area   

1. O-ring in trigger valve is damaged. 

2. Trigger valve head are damage. 

3. Trigger valve stem, seal or O-ring are 

damaged. 

1. Check and replace O-ring. 

2. Check and replace. 

3.Check and replace trigger valve stem, 

seal or O-ring 

Air leak near bottom of tool.  1. Loose screws. 

2. Worn or damaged O-rings or bumper. 

1. Tighten screws. 

2. Check and replace O-rings or bumper. 

Air  leak  between  body  and 

cylinder cap. 

1. Loose screws. 

2. Worn or damaged O-rings or seals. 

1. Tighten screw. 

2. Check and replace O-rings or bumper. 

Blade  driving  fastener  too 

deep. 

1. Worn bumper. 

2. Air pressure is too high. 

1. Replace bumper. 

2. Adjust the air pressure. 

Tool  does  not  operate  well: 

can  not  drive  fastener  or 

operate sluggishly.   

1. Inadequate air supply. 

2. Inadequate lubrication. 

3. Worn or damaged O-rings or seals. 

4.  Exhaust  port  in  cylinder  head  is 

blocked. 

1. Verify adequate air supply. 

2. Place 2 or 6 drops of oil into air inlet. 

3. Check and replace O-rings or seal. 

4. Replace damaged internal parts. 

Tool skips fasteners. 

1. Worn bumper or damaged spring. 

2. Dirt in front plate. 

3.  Dirt  or  damage  prevents  fasteners 

from moving freely in magazine. 

4. Worn or dry O-ring on piston or lack of 

Lubrication. 

5. Cylinder covers seal leaking. 

1. Replace bumper or pusher spring. 

2. Clean drive channel on front plate. 

3. Magazine needs to be cleaned. 

4. O-ring needs to be replaced. 

    And lubricate. 

5. Replace Sealing washer. 

Tool jams. 

1. Incorrect or damaged fasteners. 

2. Damaged or worn driver guide. 

3. Magazine or nose screw loose. 

4. Magazine is dirty. 

1. Change and use correct fastener. 

2. Check and replace the driver. 

3. Tighten the magazine. 

4. Clean the magazine. 

 

Содержание LT50











Отзывы: