Aeropro LT50 Скачать руководство пользователя страница 3

Air Finish nailer LT50             

        Http://www.aeroprotools.com 

 

2. Special references 

2.1 Instructions 

The  following  standard  is  applicable  to  fastener  driving  tools;  EN792-

13:2000+A1:2008”Hand-held 

non-electric power tools-safety requirements 

– Part 13: Fastener driving tools”. 

This standard requires that 

-

 

only  those  fasteners  which  are  specified  in  the  operating  instructions  (see  TECHNICAL 

DATA)shall be used in fastener driving tools. The fastener driving tool and the fasteners specified 

in the operating instructions are to be considered as one unit safety system; 

-

 

quick  action  couplings  shall  be  used  for  connection  to  the  compressed  air  system  and  the 

non-sealable nipple must be fitted at the tool in such a way that no compressed air remains in the 

tool after disconnection; 

-

 

oxygen or combustible gases shall not be used as an energy source for compressed air operated 

fastener driving tools; 

-

 

fastener  driving  tools  shall  only  be  connected  to  an  air-supply  where  the  maximum  allowable 

pressure  of  the  tool  cannot  be  exceeded  by  more  than  10%;in  the  case  of  higher  pressure  ,a 

pressure  reducing  valve  which  includes  a  downstream  safety  valve  shall  be  built  into  the 

compressed air supply;   

-

 

only spare parts specified  by  the manufacturer or his authorized representative  shall be used  in 

the repair of fastener driving tools; 

-

 

repairs  shall  be  carried  out  only  by  the  manufacturers  authorized  agents  or  by  other  experts, 

having due regard to the information given in the operating instructions. 

-

 

stands for mounting the fastener driving tools to a support, for example to a work table, shall be 

designed and constructed by the stand manufacturer in such a way that the fastener driving tools 

can  be  safely  fixed  for  the  intended  use,  thus  for  example  avoiding  damage,  distortion, 

displacement. 

Special  fields  of  application  for  the  fastener  driving  tool  may  require  the  observance  of  additional 

provisions and regulations. 

-

 

only the main energy and lubricants listed in the operating instructions may be used: 

-

 

fastener driving tools marked with an inverted equilateral triangle standing on one point may only 

be used with an effective safety yoke; 

-

 

for the maintenance of fastener driving tools, only spare parts specified by the manufacturer or his 

authorized representative shall be used; 

-

 

repairs shall be carried out only by agents authorized by the manufacturer or by other specialists, 

having due regard to the information given in the operating instructions; 

-

 

        NOTE:  Specialists  are  those  who,  as  a  result  by  professional  training  or  experience,  have 

sufficient  expertise  in  the  field  of  fastener  driving  tools  and  sufficient  familiarity  with  relevant 

govemmental  industrial  protection  provisions,  accident  prevention  regulations,  directives  and 

generally  recognized  technical  regulations(e.g.  CEN-and  CENELEC-standards),to  be  able  to 

assess the safe working condition of fastener driving tools.

 

 

 

 

 

 

 

Содержание LT50











Отзывы: