Aeropro LT50 Скачать руководство пользователя страница 4

Air Finish nailer LT50             

        Http://www.aeroprotools.com 

 

Fig 2 

 

2.2 Noise emission 

The  characteristic  noise  values  for  the  fastener  driving  tool  have  been  determined  in  accordance  with 

EN12549:1999  and  EN  ISO4871

”Acoustics-Noise  test  code  for  fastener  driving  tools-Engineering 

method”(see Technical Data). 

These values are tool-related characteristic values and do not represent the  noise development at the 

point of use. Noise development at the point of use will for example depend on the working environment, 

the work piece, the work piece support and the number of driving operations, etc. 

Depending in the conditions at the workplace and the form of the workplace, individual noise attenuation 

measures  may  need  to  be  carried  out,  such  as  placing  work  pieces  on  sound-damping  supports, 

preventing work piece vibration by means of clamping or covering, adjusting to the minimum air pressure 

required for the operation involved, etc, 

It is necessary to wear hearing protection equipment. 

                 

2.3 Information on mechanical impact (vibration) 

The characteristic vibration values for the fastener driving tool have been determined in accordance with 

ISO  8662-11:1999  and  EN  12096 

–  Measurement  of  vibration  in  hand-held  power  tools  –  Part 

11:Fastener driving tools(see Technical Data). 

This  value  is  a  tool-related  characteristic  value  and  does  not  represent  the  influence  to  the 

hand-arm-system when using the tool. An influence to the hand-arm-system when using the tool will for 

example depend on the gripping force, the contact pressure force, the working direction, the adjustment 

of energy supply, the workplace, the work piece support. 

 

2.4 Safety of the fastener driving tool 

-

 

Check prior to each operation that the safety and triggering mechanism is functioning properly and 

that all nuts and bolts are right. 

-

 

Do not carry out any alterations to the fastener driving tool without the manufactures authorization. 

-

 

Do not disassemble or make inoperative any parts of the fastener driving tool such as the safety 

yoke. 

-

 

Do not perform any” emergency repairs” without proper tools and equipment. 

-

 

The fastener driving tool should be serviced properly and at regular intervals in accordance with 
the Manufacturer’s instructions. 

-

 

Avoid weakening or damaging the too, for example by: 

punching or engraving; 

modification not authorized by the manufacturer 

guiding against templates made of hard material such as steel; 

use the equipment as a hammer; 

applying excessive force of any kind 

 

2.5 Safety at work 

Never point any operational fastener driving tool at yourself or at any other person or 

animals. 

Hold  the  fastener  driving  tool  during  the  work  operation  in  such  a  way  that  no 

injuries  can  be  caused  to  the  head  or  to  the  body  in  the  event  of  possible  recoil 

consequent  upon  a  disruption  in  the  energy  supply  or  hard  areas  within  the 

workplace.

see fig 2

 

Содержание LT50











Отзывы: