Aeropro LT50 Скачать руководство пользователя страница 5

Air Finish nailer LT50             

        Http://www.aeroprotools.com 

 

Fig 3 

 

Never  actuate  the  fastener  driving  tool  into  free  space.  This  will  avoid  any 

hazard caused by free flying fasteners and excessive strain of the tool. 

The  tool  shall  be  disconnected  from  the  compressed  air  system  for  the 

purpose  of  transportation,  especially  where  ladders  are  used  or  where  an 

unusual physical posture is adopted whilst moving(see Fig 3). 

Carry  the  fastener  driving  tool  at  the  workplace  using  only  the  handle,  and 

never with the trigger actuated. 

Take  conditions  at  the  workplace  into  account.  Fasteners  can  penetrate  thin  work  pieces  or  slip  off 

corners and edges of workplaces, and thus put people at risk. 

For personal safety, use protective equipment such ad hearing and eye protection (see fig 2) 

IMPORTANT:  DO NOT

  direct  the  adjustable  vent  hole  to  the  operator  or  other  person  or  animals 

during the use.

 

2.6 Triggering devices 

Fastener driving tools are operated by actuating the trigger using finger pressure. 

In  addition,  fastener  driving  tool  is  fitted  with  a  safety  yoke  which  enables  the  driving  operation  to  be 

carried out only after the muzzle of the tool is pressed against a work piece, These tool are marked with 

an  inverted  triangle(      )  behind  the  serial  number  and  are  not  permitted  for  use  without  an  effective 

safety yoke. 

2.7 Actuating systems 

Depending  on  their  purpose,  fastener  driving  tool  is  fitted  with  actuating  system  of  single  sequential 

actuation and contact actuation. 

You could switch to one nail figure to choose single sequential actuation, and switch to two nail figure to 

choose contact actuation. 

- Single sequential actuation: An actuating system in which the trigger and the safety  yoke have to be 

activated so the only one single driving operation is actuated via the trigger after the muzzle of the tool 

has been applied to the driving location, Thereafter further driving operations can only be performed after 

the trigger has been returned to the non driving position whilst the safety yoke remains depressed. 

-Contact actuation (restricted version):An actuating system in which the trigger and the safety yoke have 

to be  actuated for each driving operation,  with the order of  actuation not being  specified .For repeated 

driving  operations,  it  is  sufficient  if  either  the  trigger  remains  activated  and  the  safety  yoke  is  activated 

thereafter, or vice versa. 
Fastener driving tools equipped with contact actuation must be marked with the symbol” Do not use on 
scaffoldings, ladders’ (see Fig.4) and shall not be used for specific application for example: 

-

 

when changing one driving location to another involves the use of scaffoldings, stairs, ladders, or 

ladder alike constructions, e.g. roof    laths; 

-

 

closing boxes or crates; 

-

 

fitting transportation safety systems e.g. on vehicles and wagons. 

 

 

                                                                                                                      Colours: 

                                                                                                                      Red on white ground, 

                                                                                                                      fastener driving tools and   

                                                                                                                      ladder black 

 

 

 

Fig. 4

: Symbol” Do not use on scaffoldings, ladders” 

Содержание LT50











Отзывы: