Aeropro LT50 Скачать руководство пользователя страница 6

Air Finish nailer LT50             

        Http://www.aeroprotools.com 

 

3 .Compressed air system 

 

 

 

 

Proper  functioning  of  the  fastener  driving  tool  requires  filtered,  dry  and  lubricated  compressed  air  in 

adequate quantities. 

If  the  air  pressure  in  the  line  system  exceeds  the  maximum  allowable  of  the  fastener  driving  tool,  a 

pressure reducing valve followed by a downstream safety valve shall additionally be fitted in the supply 

line to the tool. 

            NOTE:  When  compressed  air  is  generated  by  compressors,  the  natural  moisture  in  the  air 

condenses and collects as condensed water in pressure vessels and pipelines. This condensate 

must be removed by water separators. These water separators must be checked on a daily basis 

and if necessary drained, since corrosion can otherwise develop in the compressed air system 

and in the fastener driving tool. Which serves to accelerate wear? 

The  compressor  plant  shall  be  adequately  dimensioned  in  terms  of  pressure  output  and  performance 

(volumetric  flow)  for  the  consumption  which  is  to  be  expected.  Line  sections  which  are  too  small  in 

relation to the length of the line (pipes and hoses), as well as overloading the compressor, will result in 

pressure drops. 

Permanently  laid  compressed  air  pipelines  should  have  an  internal  diameter  of  at  least  19  mm  and  a 

corresponding large diameter where relatively long pipelines or multiple users are involved. 

Compressed  air  pipelines  should  be  laid  so  as  to form  a  gradient (highest  point  in  the  direction  to the 

compressor).Easily accessible water separators should be installed at the lowest points. 

Junctions for users should be joined to the pipelines from above, 

Connecting  points  for  fastener  driving  tools  should  be  fitted  with  a  compressed  air  servicing 

unit(filter/water separator/oiler)directly at the junction point. 

Oilers must be checked on a daily basis and if necessary topped up with the recommended grade of oil 

(see  TECHNICAL  DATA).  Where  hose  lengths  of  over  10  m  are  used.,  the  oil  supply  for  the  fastener 

driving tool cannot be guaranteed, We therefore recommend that 2to 5drops (depending on the loading 

of the fastener driving tool)of the recommended oil (see TECHNICAL DATA) should be added via the air 

inlet of the tool, or an oiler attached directly to the fastener driving tool. (see fig 5) 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING

 

Never free-fire the tool at high pressure. 

 

Содержание LT50











Отзывы: