manualshive.com logo in svg

Aeroflex Gaisler RT-SPW-ROUTER, Руководство пользователя

Поделиться
Скачать
Aeroflex Gaisler RT-SPW-ROUTER Скачать руководство пользователя страница 49

AEROFLEX GAISLER

49

RT-SPW-ROUTER

Copyright Aeroflex Gaisler AB

June 2012, Version 1.2

Table 35. GRSPWROUTER registers

RMAP address

Register

0x0

RESERVED

0x4-0x7C

Port setup for ports 1-31

0x80-0x3FC

Port setup for logical addresses 32-255

0x400-0x47C

RESERVED

0x480-0x7FC

Routing table entry for logical addresses 32-255

0x800-0x87C

Port 0-31 control

0x880-0x8FC

Port 0-31 status

0x900-0x97C

Timer reload ports 0-31

0xA00

Router configuration/status

0xA04

Time-code

0xA08

Version/instance ID

0xA0C

Initialization divisor

0xA10

Configuration write enable

0xA14

Timer prescaler reload

0xC04-0xC7C

Port 1-31 outgoing character count

0xC84-CFC

Port 1-31 incoming character count

0xD04-0xD7C

Port 1-31 outgoing packet count

0xD84-0xDFC

Port 1-31 incoming packet count

Table 36.  Port setup register

31

1

0

PORT ENABLE BITS

PD

NR

NR

31: 1

Port enable bits (PORT ENABLE BITS) - Each individual bit enables, when set to 1, packets with the
path or logical address corresponding to this port setup register to be sent on the port with the same num-
ber as the bit index. Only bits up to and including the highest port number are valid.

rw

0

Packet distribution (PD) - When set to 1 packet distribution is used for the path or logical address corre-
sponding to this port setup register. When set to 0 group adaptive routing is used.

rw

NOTE: When this register has been written with a non-zero value it will be considered valid and used for determining the
destination port. A memory error at location of the port setup information for the destination address will cause the packet to
be discarded which will make the associated physical address unusable until the error is fixed (done automatically if auto-
scrubbing is enabled). If this behavior is unacceptable GAR or PD should not be enabled for physical addresses. If a port
setup entry for a physical address is valid it can be invalidated by writing zeros (to the valid bits in the register) to the mem-
ory location.

Содержание RT-SPW-ROUTER





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды