Advanced Navigation Spatial FOG Dual ETH Скачать руководство пользователя страница 10

Страница: 10 / 30

Spatial FOG Dual ETH

Supplementary Reference Manual

Page 9 of 29

Version 1.2
10/09/2019

Specifications

8.1

Mechanical Drawings

Refer to the Spatial FOG Dual Reference Manual.

8.2

Navigation Specifications

Refer to the Spatial FOG Dual Reference Manual.

8.3

Heading Accuracy

Refer to the Spatial FOG Dual Reference Manual.

8.4

Sensor Specifications

Refer to the Spatial FOG Dual Reference Manual.

8.5

GNSS Specifications

Refer to the Spatial FOG Dual Reference Manual.

8.6

Communication Specifications

Parameter

Value

Primary Interface

Ethernet TCP

Primary Protocol

AN Packet Protocol (ANPP)

Auxiliary Interface

RS232

Auxiliary Protocol

External data ANPP input & output

Serial input & output

GPIO Interface

RS422

GPIO Protocol

Digital and frequency input only

Ethernet Speed

10Base-T or 100Base-Tx (auto sensing)

Auxiliary Speed

4800 to 2 M baud

GPIO Speed

4800 to 2 M baud

Table 3: Communication specifications

Note the GNSS Receiver port is not directly accessible.

8.7

Hardware Specifications

Refer to the Spatial FOG Dual Reference Manual.

Содержание Spatial FOG Dual ETH































Результаты поиска

Содержание Spatial FOG Dual ETH

Отзывы:

Похожие инструкции для Spatial FOG Dual ETH

Бренды по названию

Популярные бренды

Advanced Navigation Spatial FOG Dual ETH, Справочное руководство

Результаты поиска

Содержание Spatial FOG Dual ETH

Отзывы:

Похожие инструкции для Spatial FOG Dual ETH

Бренды по названию

Популярные бренды