Advanced Electronic Applications PK-88 Скачать руководство пользователя страница 98

Страница: 98 / 169

PK-88 OPERATING MANUAL

COMMAND SUMMARY

5 - 23

PK-88 - 98

CMDTIME

Mnemonic: CM

Default: 10

Parameters:

0 to 250 specifies timeout value in 100-millisecond intervals while in Trans-
parent Mode.

is 0 (zero), exit from Transparent Mode requires sending the BREAK signal or interrupting

power to the PK-88.

CMDTIME sets the timeout value in Transparent Mode. A guard time of

seconds allows escape to

Command Mode from Transparent Mode, while permitting any character to be sent as data.

The same Command Mode entry character (default

[^C]

) used to exit from the Converse Mode is

used to exit Transparent Mode, although the procedure is different.

The Command Mode entry character is set by COMMAND.
Three Command Mode entry characters must be entered less than

seconds apart, with no in-

tervening characters, after a delay of

seconds following the last characters typed.

After a final delay of

seconds, the PK-88 exits Transparent Mode and enters Command Mode.

You will then see the normal Command Mode prompt:

cmd:

The following diagram illustrates this timing:

CMSG

ON|OFF

Mnemonic:

CMS

Default: OFF

Parameters:

The stored CTEXT message is sent as the first packet after a connection is
established by a connect request from a distant station.

OFF

The text message is not sent at all.

CMSG enables or disables automatic transmission of the CTEXT message when your PK-88 accepts
a connect request from another station.

⇒

Set

CMSG ON

to tell callers that you are not available to answer calls manually when they con-

nect to your PK-88.

⇒

Set

CMSG OFF

when available to operate or answer calls manually.

COMMAND

Mnemonic:

COM

Default: $03 <CTRL-C>

Parameters:

0 to $7F (0 to 127 decimal) specifies an ASCII character code.

COMMAND is used to change the Command Mode entry character. You can enter the code in either
hexadecimal or decimal numbers.

Содержание PK-88










































































































































































Результаты поиска

Содержание PK-88

Отзывы:

Похожие инструкции для PK-88

Бренды по названию

Популярные бренды

Advanced Electronic Applications PK-88, Руководство по эксплуатации

Результаты поиска

Содержание PK-88

Отзывы:

Похожие инструкции для PK-88

Бренды по названию

Популярные бренды