Advanced Electronic Applications PK-88 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 169

background image

PK-88 OPERATING MANUAL

INSTALLATION

2 - 6

PK-88 - 22

13.

Type

C AAA

followed by a

[RETURN]

. After a few moments, your monitor should dis-

play:

cmd:

c aaa

*** CONNECTED to AAA

14.

Type a few characters, any characters, followed by a

[

↵

]

. After a few moments,

your monitor should echo the same characters that you have just typed.

15.

Type

[^C]

) (type

[C]

while pressing the

[CONTROL]

key down). Your monitor

should respond with:

cmd:

16.

Type

HB 300

followed by a

[RETURN]

. Your monitor should respond with:

HBAUD was 1200
HBAUD now 300

17.

Type

[K]

followed by a

[RETURN]

. Your monitor should echo the characters you've

just typed.

18.

Type

[^C]

. Your monitor should respond with:

cmd:

19.

Type

[D]

followed by a

[

↵

]

. Your monitor should respond with:

cmd:

d

*** DISCONNECTED: AAA

20.

If you have done all these steps successfully, you have completed the system instal-
lation and you are ready to begin operating.

21.

If you have problems with the steps shown above, return to Step 1 AFTER checking
all cables and connectors. Read each step again carefully. If you still have problems,
shut down the PK-88 and contact our Customer Service Department as suggested in
the front of this manual.

If all the front-panel LEDs remain lit at system start, verify that your power supply
can provide at least 600 ma. at 12 VDC.

2.8

Radio Connections and Setup

DISCONNECT ALL POWER BEFORE MAKING ANY OTHER CONNECTIONS!

Use this simple step-by-step routine to verify that all cables and connectors are properly in-
stalled, and that the PK-88 Packet Controller is operating correctly. The procedure will also
help you become familiar with the software commands and responses.

If you cannot solve a problem after carefully reading this manual and checking all cables
and connectors, please refer to the instructions for calling the manufacturer in the beginning
of the manual.

«
...
20
21
22
23
24
...
»

Содержание PK-88










































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PK-88

Бренд: Samson Страницы: 48

Бренд: Mako Networks Страницы: 15

Бренд: Raymarine Страницы: 12

Бренд: Jafar Страницы: 13

Бренд: KAR-TECH Страницы: 28

Бренд: 2M Technology Страницы: 17

Бренд: 2iB Страницы: 5

Go!Control Panel

Бренд: 2gig Technologies Страницы: 78

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

COOPER POWER SERIES

Бренд: Eaton Страницы: 50

Бренд: Watts Страницы: 4

Temp Alert TA2HL

Бренд: Winland Electronics Страницы: 2

Бренд: Euromatic Страницы: 20

Бренд: VMK Страницы: 98

AQUIS ULTRAFLOW

Бренд: Waterous Страницы: 217

Бренд: Xilinx Страницы: 101

Бренд: Burkert Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды