Advance acoustic Adfinity 17ST Скачать руководство пользователя страница 75

Страница: 75 / 92

SERVICE MANUAL

ENGLISH

Adfinity™ 17ST / 20ST / X20R / 20D / X20D / X20C / X24D

9096982000

OTHER SYSTEM

SCREW AND NUT TIGHTENING CHECK

1. Drive the machine to the appointed disposal area, and empty the recovery water tank (21) with the hose (16).

2. Place the machine on a hoisting system (if available).

Otherwise, drive the machine on a level floor.

3. • (For

Adfinity™ X20R, 20D, X20D, X20C, X24D

) Turn the ignition key (80) to “0”.

• (For

Adfinity™ 17ST, 20ST

) Turn off the switches (71) and (73).

4. Grasp the handle (41) and carefully lift the tank (40).

5. Check:

• Tightening of mounting screws and nuts;

• Correct position of fasteners;

• Visible faults in the components;

• Leaks of fluids.

6. Carefully lower the tank (40).

7. Remove the machine from the hoisting system.

Содержание Adfinity 17ST





























































































Результаты поиска

Содержание Adfinity 17ST

Отзывы:

Похожие инструкции для Adfinity 17ST

Бренды по названию

Популярные бренды

Advance acoustic Adfinity 17ST, Руководство по обслуживанию

Результаты поиска

Содержание Adfinity 17ST

Отзывы:

Похожие инструкции для Adfinity 17ST

Бренды по названию

Популярные бренды