Advance acoustic Adfinity 17ST Скачать руководство пользователя страница 25

Страница: 25 / 92

SERVICE MANUAL

ENGLISH

Adfinity™ 17ST / 20ST / X20R / 20D / X20D / X20C / X24D

9096982000

ECOFLEX™ SYSTEM

CLEAN WATER FILTER CLEANING (For Adfinity™ X20D, X20C, X24D)

1. Drive the machine on a level floor.

2. Turn the ignition key (80) to “0”.

3. Open the cover (22) and check that the recovery water tank (21) is empty, otherwise empty it with the drain hose (16).

4. Grasp the handle (41) and carefully lift the tank (40).

5. Slightly lift the hoses (A), then, operating on the clean water filter assembly (F), unscrew the transparent cover (B) and remove

the filter strainer (C). Clean and install them on the support (D).

NOTE

The filter strainer (C) must be correctly positioned on the housing (E) of the support (D).

6. Install the hoses (A) and the filter assembly (F).

S301524A

Содержание Adfinity 17ST





























































































Результаты поиска

Содержание Adfinity 17ST

Отзывы:

Похожие инструкции для Adfinity 17ST

Бренды по названию

Популярные бренды

Advance acoustic Adfinity 17ST, Руководство по обслуживанию

Результаты поиска

Содержание Adfinity 17ST

Отзывы:

Похожие инструкции для Adfinity 17ST

Бренды по названию

Популярные бренды