Advance acoustic Adfinity 17ST Скачать руководство пользователя страница 63

Страница: 63 / 92

SERVICE MANUAL

ENGLISH

Adfinity™ 17ST / 20ST / X20R / 20D / X20D / X20C / X24D

9096982000

RECOVERY WATER SYSTEM

VACUUM SYSTEM MOTOR FILTER CLEANING

Disassembly and cleaning

1. If the tank (21) contains recovery water:

• Drive the machine to the appointed recovery water disposal area.

• (For

Adfinity

X20R, 20D, X20D, X20C, X24D

) Turn the ignition key (80) to “0”.

• (For

Adfinity

17ST, 20ST

) Turn off the switches (71) and (73).

• Empty the recovery water tank (21) with the hose (16).

2. Drive the machine on a level floor.

3. • (For

Adfinity™ X20R, 20D, X20D, X20C, X24D

) Turn the ignition key (80) to “0”.

• (For

Adfinity™ 17ST, 20ST

) Turn off the switches (71) and (73).

4. Grasp the handle (41) and carefully lift the tank (40).

5. Remove the vacuum system motor filter (44) and clean it with water and compressed air.

6. Install the filter (44).

Assembly

7. Assemble the components in the reverse order of disassembly.

VACUUM SYSTEM MOTOR ELECTRICAL INPUT CHECK

WARNING!

This procedure must be performed by qualified personnel only.

1. If the tank (21) contains recovery water:

• Drive the machine to the appointed recovery water disposal area.

• (For

Adfinity™ X20R, 20D, X20D, X20C, X24D

) Turn the ignition key (80) to “0”.

• (For

Adfinity™ 17ST, 20ST

) Turn off the switches (71) and (73).

• Empty the recovery water tank (21) with the hose (16).

2. Drive the machine on a level floor.

3. • (For

Adfinity

X20R, 20D, X20D, X20C, X24D

) Turn the ignition key (80) to “0”.

• (For) Turn off the switches (71) and (73).

4. Disconnect the battery connector (12).

5. Grasp the handle (41) and carefully lift the tank (40).

6. Apply the amperometric pliers (A) on one cable (B) of the batteries.

7. - (For

Adfinity™ X20R, 20D, X20D, X20C, X24D

) Turn the ignition key (80) to “I”.

8. - Turn on the vacuum system by pressing the switch (73) and check that the motor electrical input is 16 - 19 A at 24 V.

Turn off the vacuum system by pressing the switch (73).

Remove the amperometric pliers (B).

If the electrical input exceeds the specifications, check the motor carbon brushes

(see the procedure in the relevant paragraph).

If necessary, disassemble the vacuum system motor (see the procedure in the relevant paragraph),

and check the condition of all its components.

If the above-mentioned procedures do not lead to a correct electrical input, the motor must be replaced

(see the procedure in the relevant paragraph).

9. Perform steps 4 and 5 in the reverse order.

S301553A

Содержание Adfinity 17ST





























































































Результаты поиска

Содержание Adfinity 17ST

Отзывы:

Похожие инструкции для Adfinity 17ST

Бренды по названию

Популярные бренды

Advance acoustic Adfinity 17ST, Руководство по обслуживанию

Результаты поиска

Содержание Adfinity 17ST

Отзывы:

Похожие инструкции для Adfinity 17ST

Бренды по названию

Популярные бренды