Advance acoustic Adfinity 17ST Скачать руководство пользователя страница 65

Страница: 65 / 92

SERVICE MANUAL

ENGLISH

Adfinity™ 17ST / 20ST / X20R / 20D / X20D / X20C / X24D

9096982000

RECOVERY WATER SYSTEM

VACUUM SYSTEM MOTOR DISASSEMBLY/ASSEMBLY

Disassembly

1. If the tank (21) contains recovery water:

• Drive the machine to the appointed recovery water disposal area.

• (For

Adfinity™ X20R, 20D, X20D, X20C, X24D

) Turn the ignition key (80) to “0”.

• (For

Adfinity™ 17ST, 20ST

) Turn off the switches (71) and (73).

• Empty the recovery water tank (21) with the hose (16).

2. Drive the machine on a level floor.

3. • (For

Adfinity™ X20R, 20D, X20D, X20C, X24D

) Turn the ignition key (80) to “0”.

• (For

Adfinity™ 17ST, 20ST

) Turn off the switches (71) and (73).

4. Disconnect the battery connector (12).

5. Grasp the handle (41) and carefully lift the tank (40).

6. Remove the screws (A) and recover the washers.

7. Remove the motor cover (B).

8. Remove the filter (C) and the gasket (D).

9. Remove the motor (E), the sound-deadening pipe (F) and the sound-deadening panel (G).

10. Disconnect the electrical connector (H) of the motor (E).

11. Check the efficiency of the gasket (I) and, if necessary, replace it.

Assembly

12. Assemble the components in the reverse order of disassembly, and note the following:

• If necessary, clean the filter (C) before assembling it (see the procedure in the relevant paragraph).

S301556A

Содержание Adfinity 17ST





























































































Результаты поиска

Содержание Adfinity 17ST

Отзывы:

Похожие инструкции для Adfinity 17ST

Бренды по названию

Популярные бренды

Advance acoustic Adfinity 17ST, Руководство по обслуживанию

Результаты поиска

Содержание Adfinity 17ST

Отзывы:

Похожие инструкции для Adfinity 17ST

Бренды по названию

Популярные бренды