Advance acoustic Adfinity 17ST Скачать руководство пользователя страница 66

Страница: 66 / 92

ENGLISH

SERVICE MANUAL

9096982000

Adfinity™ 17ST / 20ST / X20R / 20D / X20D / X20C / X24D

RECOVERY WATER SYSTEM

SQUEEGEE SPRING CHECK/REPLACEMENT (All models, with aluminium squeegee)

Check

1. Drive the machine on a level floor.

2. • (For

Adfinity™ X20R, 20D, X20D, X20C, X24D

) Turn the ignition key (80) to “0”.

• (For

Adfinity™ 17ST, 20ST

) Turn off the switches (71) and (73).

3. Check that the springs (A) and (B) push the squeegee (C) on the floor correctly.

4. If necessary, disassemble and replace the springs according to the following procedure.

Disassembly

5. Remove the squeegee (see the procedure in the relevant paragraph).

6. Lift the deck by pressing the pedal (11).

7. Grasp the handlebar (2) and lower the front part of the machine.

8. Remove the cotter pin (D).

9. Disengage the end (E) of the left spring (F) from the housing (G).

10. Remove the left spring (F).

11. Repeat steps 8, 9 and 10 for the right spring (H).

Assembly

12. Assemble the springs by performing steps 5 to 11 in the reverse order.

S301557A

Содержание Adfinity 17ST





























































































Результаты поиска

Содержание Adfinity 17ST

Отзывы:

Похожие инструкции для Adfinity 17ST

Бренды по названию

Популярные бренды

Advance acoustic Adfinity 17ST, Руководство по обслуживанию

Результаты поиска

Содержание Adfinity 17ST

Отзывы:

Похожие инструкции для Adfinity 17ST

Бренды по названию

Популярные бренды