ADTRAN Express XL 1200070L1 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 187

background image

Chapter 3: Terminal Menu Operation and Structure

60

Express XL/XLT User Manual

61200.070L1-1

Filter Defines /Pattern Filter Defines

Write security: 2; Read security: 3
The pattern filter is applied to bridge packets only. That is any packet which
is forwarded by the bridge functionality of the Express XL/XLT. Up to 32 pat-
tern defines can be specified.

Name

Identifies the filter entry

Offset

Offset from beginning of packet of where to start

the pattern comparison

Pattern

64 bits used for comparison.

(hexadecimal format)

Mask

Bits in the pattern to be compared.

(hexadecimal format)

Filter Defines /IP Filter Defines

Write security: 2; Read security: 3
The IP filter defines apply to any IP packet, whether it is routed or bridged. Up
to 32 IP defines can be specified.

Name

Identifies the filter entry

IP Src

IP address compared to the source address.

(dotted decimal format)

Src Mask

Bits which are used in the source comparison.

(dotted decimal format)

IP Dest

IP address compared to the destination address.

(dotted decimal format)

Dest Mask

Bits which are used in the destination

comparison. (dotted decimal format)

Src Port

IP source port number used for comparison

Range: 0 to 65535. (decimal format)

Src Port Cmpr

Type of comparison that is performed

=

- means ports equal to

not =

-

means port not equal to

>

- means port greater than

<

- means port less than

None

- means the source port is not compared

Dst Port

IP destination port number used for

comparison Range: 0 to 65535. (decimal format)

«
...
74
75
76
77
78
...
»

Содержание Express XL 1200070L1




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express XL 1200070L1

8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink

Бренд: Tyco Electronics Страницы: 18

Бренд: H3C Страницы: 45

Бренд: H3C Страницы: 80

Бренд: H3C Страницы: 46

Бренд: H3C Страницы: 45

Бренд: H3C Страницы: 4

Бренд: H3C Страницы: 184

Бренд: TP-Link Страницы: 73

Бренд: Netopia Страницы: 38

Бренд: EMCIS Страницы: 14

Бренд: ICP DAS USA Страницы: 8

Бренд: E-LINX Страницы: 24

Бренд: Z-Wave Страницы: 6

Easy Tool-ID BSG TID-05-T30-00-005

Бренд: Balluff Страницы: 46

memonizerWORKSTATION

Бренд: MEMON Страницы: 2

FlexNetwork 5130 Series

Бренд: HPE Страницы: 33

AirStation WZR-1166DHP

Бренд: Buffalo Страницы: 2

Бренд: Comway Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды