ADTRAN Express XL 1200070L1 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 187

background image

Chapter 3: Terminal Menu Operation and Structure

38

Express XL/XLT User Manual

61200.070L1-1

Dial Line/LDN 1 or 2

Write security: 2; Read security: 5
This option allows the entry of 0, 1, or 2 LDNs. The LDN is used when placing
or receiving calls. The LDN is the local phone number assigned to the line.

LDN 1 = 5 5 5 1 2 1 2
LDN 2 = 5 5 5 1 2 1 3

Disconnect the network interface from the unit before initially entering or altering the

SPIDs and LDNs.

ISDN/Leased Line

Write security: 2; Read security: 5
Leased Line parameters are entered under this menu. Leased mode would be
used for permanent circuits.

Leased Line/Clock Mode

Write security: 2; Read security: 5
The clock mode determines which unit will supply the clock for synchroniza-
tion. If the two units are connected through channel banks, both units should
be configured for Slave mode.

Slave (def)

Timing is derived from the master unit.

Master

Timing is derived from this unit.

Leased Line/Channel Rate

Write security: 2; Read security: 5

64k

Only B1 is used.

2x64k

B1 and B2 go to different locations.

128k

(def)

B1 and B2 are used together.

144k

B1, B2 and D are used together.

ISDN/NEBEs

Read security: 5
This contains the number of Near-End-Block-Errors (NEBEs) that have been
detected by the Express XL/XLT’s ISDN circuitry. Continuous errors can in-
dicate a line problem, but a burst at one time is normal.

«
...
52
53
54
55
56
...
»

Содержание Express XL 1200070L1




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express XL 1200070L1

Бренд: H3C Страницы: 1057

Бренд: Eaton Страницы: 10

Бренд: QNO Страницы: 106

Бренд: Face Страницы: 8

Бренд: STONEFLY Страницы: 48

Бренд: Conceptronic Страницы: 230

Бренд: NA Страницы: 22

8677 - BladeCenter Rack-mountable - Power Supply

Бренд: IBM Страницы: 126

Fan Tray 8820-S2-900

Бренд: Paradyne Страницы: 6

Бренд: Grundig Страницы: 24

Бренд: Asante Страницы: 150

Бренд: Xyclop Страницы: 144

Бренд: Silvertel Страницы: 9

Бренд: iDirect Страницы: 72

Бренд: Alcatel-Lucent Страницы: 60

Бренд: Tenda Страницы: 120

Бренд: TRENDnet Страницы: 10

Бренд: ZyXEL Communications Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды