ADTRAN Express XL 1200070L1 Скачать руководство пользователя страница 104

Страница: 104 / 187

Chapter 3: Terminal Menu Operation and Structure

Express XL/XLT User Manual

61200.070L1-1

DIAL MENU

The Dial menu is used for dialing the Connection List profile setup under

Con-

figuration/Connection List

and for checking the status of each Connection

List. This list is in the same order as the Connection List entries. Figure 3-10
shows the Dial menu.

Figure 3-10

Dial Screen

Dial/Description

Read security: 5
This read-only field is the name entered for the profile under

Configuration/

Connection List/Description

Dial/Dial

Write security: 4; Read security: 5
This is an activator used for dialing the phone numbers in the profile. Place
the cursor over the field and press

Enter

to activate the dialing function.

Содержание Express XL 1200070L1




























































































































































































Результаты поиска

Содержание Express XL 1200070L1

Отзывы:

ADTRAN Express XL 1200070L1, Руководство пользователя, Страница: 104 / 187

Результаты поиска

Содержание Express XL 1200070L1

Отзывы: