ADTRAN Express XL 1200070L1 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 187

background image

Quick Startup Guide

4

Express XL/XLT User Manual

61200.070L1-1

11. Enter the

IP address

and

Netmask

parameters of the access server at the

remote site. This creates a static route to the access server’s network which
is entered into the Express XL/XLT’s IP route table.

12. Move the cursor over the

RIP

menu. Check with the network administra-

tor for the type of routing protocol used. The Express XL/XLT supports
RIP versions 1 and 2. The protocol is set in the

Protoco

l parameter.

13. Select

Yes

for the

Triggered

parameter. This will prevent periodic RIP up-

dates that keep the ISDN link from going “idle.”

14. Select

Yes

for the

Retain

parameter. This will allow the routes learned

from the access server to be saved in the IP routing table. Access to any of
those networks from the workstation will cause this profile to be dialed.

15. Use the left arrow to get back to the previous menu. Use the down arrow

to view the

IPX

menu parameters in the right pane.

16. This is similar to steps 13 and 14. Select

Yes

for

Triggered

and

Yes

for

Re-

tain

. This will allow the ISDN link to go to an idle state and permit the

Express XL/XLT to “spoof” the server information obtained from the ac-
cess server. A similar configuration must be selected on the access server.

17. Use the arrows to get the

Dial Out

menu parameters for this profile.

18. Enter the phone number of the access server in

Number 1

. If configured

by the administrator to use two B-channels using Multilink PPP, set the

Initial Channels

field to

2

. Some PPP protocols, if they exist in the access

server, will allow the second channel to come into play only if the band-
width is needed. If this is the case, the Express XL/XLT will automatically
negotiate this with the access server.

19. Now move to the

Bandwidth

menu for this profile. Once there, use the

right arrow to move to the

On Demand

submenu.

20. Set the

Mode

parameter to

On

. This enables the dynamic bandwidth fea-

tures of the Express XL/XLT.

21. Select the

Idle Timeout

parameter and enter the number of seconds the

Express XL/XLT should wait before hanging up the connection when no
traffic is present. A value of 120 seconds is typical. A value of 0 means nev-
er idle the link.

22. All the parameters for this Connection List profile are complete. To save

them, press the left arrow to get to the top (main) menu; when prompted

Save Connection List changes?

enter

y

.

23. Set up the computer workstation’s IP and IPX parameters as instructed by

the network administrator. The Express XL/XLT’s IP address should be
the computer’s default gateway.

«
...
18
19
20
21
22
...
»

Содержание Express XL 1200070L1




























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Express XL 1200070L1

Бренд: Hama Страницы: 10

SMART NODE 4950-NCE

Бренд: Patton electronics Страницы: 8

NetLink 2960 RAS

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 2

Бренд: Qlogic Страницы: 20

PowerBeam AC Gen2

Бренд: Ubiquiti Страницы: 22

Бренд: QNAP Страницы: 54

Бренд: BWI Страницы: 5

Бренд: X-Micro Страницы: 49

Бренд: Airlink101 Страницы: 13

UniFi WiFi BaseStation XG

Бренд: Ubiquiti Страницы: 19

Emotron OSTO 100

Бренд: CG Страницы: 112

Бренд: Tripp Lite Страницы: 3

Бренд: Variscite Страницы: 17

Бренд: HMS Страницы: 18

Бренд: 8e6 Technologies Страницы: 94

GigaVUE H TA100-CXP

Бренд: Gigamon Страницы: 115

7798 I/SITE LAN

Бренд: CSI Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды