ADTRAN Express XL 1200070L1 Скачать руководство пользователя страница 33

Страница: 33 / 187

Chapter 1: Understanding ISDN and the Express XL/XLT

61200.070L1-1

Express XL/XLT User Manual

WAN Indicators

LNK

Flashes when the link is being negotiated; solid when the link

is active.

Flashes when a call on the B1 channel is in progress; solid

when a call is connected.

Flashes when a call on the B2 channel is in progress; solid

when a call is connected.

Loop

Indicates ISDN layers status. Indicator is off when layer 1 is

down. A fast flash indicates layer 1 is up and layer 2 is down.

A slow flash indicates layer 2 is up and layer 3 is down. A sol-

id illumination indicates all layers are up.

PWR

Flashes when self-test has failed; solid when unit is powered

on and self-test has passed.

Test Indicators

ERR

Illuminates when self-test or front panel test has failed.

B1/B2

Indicates test selected by front panel buttons.

Figure 1-6

Express XL/XLT LEDs

Pushbutton Tests

The echo request test can be executed by pressing the

SELECT

button one time

and pressing

TEST

. A ping test is executed by pressing the

SELECT

button

twice and pressing

TEST

. The IP address pinged comes from the previously

pinged address set in the menu. If it is blank, the default gateway is used. If
the default gateway is blank, an error is indicated. The

ERR

indicator illumi-

nates if any pings are not returned. The dial self-test is invoked from the front
panel if the

SELECT

button is pressed three times. The LDN(s) must be al-

ready programmed for this test to work.

COL JAB

ERR

LNK

TEST

Express XL

LOOP PWR

SELECT

TEST

Содержание Express XL 1200070L1




























































































































































































Результаты поиска

Содержание Express XL 1200070L1

Отзывы:

Похожие инструкции для Express XL 1200070L1

Бренды по названию

Популярные бренды

ADTRAN Express XL 1200070L1, Руководство пользователя

Результаты поиска

Содержание Express XL 1200070L1

Отзывы:

Похожие инструкции для Express XL 1200070L1

Бренды по названию

Популярные бренды