ADTRAN Express XL 1200070L1 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 187

ADTRAN Express XL 1200070L1 Скачать руководство пользователя страница 67

Chapter 3: Terminal Menu Operation and Structure

61200.070L1-1

Express XL/XLT User Manual

51

negotiate PPP IPCP to exchange IP packets. However, if a device can only sup-
port PPP BCP, IP packets are encapsulated by the device as bridge packets.
The Express XL/XLT can treat the WAN IP Bridge as a virtual Ethernet port
connected only to a WAN device which has negotiated PPP BCP. This menu
allows the IP parameters for this virtual Ethernet to be setup.

WAN IP Bridge/Network

Write security: 2; Read security: 5
This is the IP address of the virtual Ethernet port.

WAN IP Bridge/Netmask

Write security: 2; Read security: 5
This is the network mask to be applied to the virtual Ethernet port.

WAN IP Bridge/Triggered

Write security: 2; Read security: 5
When set to

Yes

, only IP RIP updates are sent when the routing table has

changed. When set to

No

(def), updates are sent periodically. RIP version,

method, and direction are determined by the Ethernet parameters set in the

Configuration/IP/IP Router/RIP

menu.

WAN IP Bridge/Proxy ARP

If this option is set to

Yes

(def),

the Express XL/XLT will proxy ARP on the

bridge IP port. See the section IP/Proxy ARP on page 46 for an explanation of
the proxy ARP function.

Bridge/WAN IPX Bridge

When IPX routing is active, the Express XL/XLT will allow another WAN de-
vice to bridge IPX packets to it using PPP BCP. Normally, two IPX routers
would negotiate PPP IPXCP to exchange IPX packets. However, if a device
can only support PPP BCP, IPX packets are encapsulated by the device as
bridge packets. The Express XL/XLT can treat the WAN IPX Bridge as a vir-
tual Ethernet port connected only to a WAN device which has negotiated PPP
BCP. This menu allows the IPX parameters for this virtual Ethernet to be set-
up.

«
...
65
66
67
68
69
...
»

Содержание Express XL 1200070L1




























































































































































































Отзывы:

Нет отзывов