manualshive.com logo in svg

ADT SERIES 4250, Руководство пользователя

Поделиться
Скачать
ADT SERIES 4250 Скачать руководство пользователя страница 2

1

Page

INTRODUCTION ................................................................ 2

Security conditions .................................................... 3
Full Set (Fully armed)................................................. 3
Part Set (Partially armed) ........................................... 3
Unset (Disarmed) ........................................................ 3

GLOSSARY OF TERMS .................................................... 4
USER CONTROL............................................................... 6
Keypad LED status indicator ........................................... 7
SETTING THE SYSTEM (TURNING THE SYSTEM ON)
Full Set (Full Arming) ........................................................ 8
Problems when selecting FULL SET

Zone fault conditions ................................................. 9
Incorrect code entry.................................................. 10
Deviation from correct Exit/Entry procedure ........... 11
Failure to complete exit procedure ......................... 12

Part Set (Partially armed)

Delay selection .......................................................... 13
Instant selection ........................................................ 13

UNSETTING THE SYSTEM (Turning the system off)
Unsetting from a FULL SET condition............................ 15
Unsetting from a FULL SET condition after Alarm
activation .......................................................................... 16

C

ONTENTS

Page

Unsetting from a PART SET condition ............................. 17
Problems when unsetting the system

Deviation from Entry route ......................................... 19
Zones not restored during entry time ........................ 19

PROCEDURE FOR RESETTING THE SYSTEM
AFTER AN ALARM INDICATION ...................................... 20
EMERGENCY DURESS ................................................... 21
VIEWING ALARM HISTORY LOG .................................... 22
SYSTEM FAULTS
Mains power failure .......................................................... 23
Backup battery failure ..................................................... 24
Telephone line faults ........................................................ 25
Tamper faults .................................................................... 27
Wiring fault conditions ..................................................... 28
TEST SIGNAL ................................................................... 29
CHIME MODE (OPTIONAL FEATURE)............................ 31
ADVANCE SYSTEM FEATURES
Adding additional access codes .................................... 33
Removing additional access codes ............................... 33
Multiple partition arming/disarming................................ 34
Omitting zones to allow system setting ......................... 35
Advanced alarm history ................................................... 36

Содержание SERIES 4250







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды