background image

–  17  – 

 

APPENDIX A 

SUMMARY OF LED OPERATION 

GSMVLP-ADT Status Display Operation 

The GSMVLP-ADT Status Display has four LEDs used to indicate message and device status (refer to 
Figure 5). When installed in the control, the LEDs appear in the following order from top to bottom. 

 

STATUS, 

green 

 

MESSAGE, 

yellow 

 

FAULT, 

red

 

 

MINIMUM SIGNAL STRENGTH, green 

Each LED can have four different states - ON, OFF, FAST BLINK and SLOW BLINK. Throughout this 
document, the key shown in Figure 7 is used to describe LED state: 

 

ON

GSMVL-002-V0

OFF

FAST BLINK

SLOW BLINK

 

Figure 7 

 LED Key 

Minimum Signal Strength LED Operation 

The Minimum Signal Strength LED normally displays the module’s signal strength.  The LED (green 
LED) will be lit to indicate that the minimum required signal strength for installation exists between 
the module and the receiving tower. Refer to Figure 8.

 

Table 3. Status and Signal Strength LED Operation 

 LED COLOR 

LED 

DESCRIPTION 

GREEN STATUS 

ON 

– GSMVLP-ADT is NOT configured with account information. 

OFF – GSMVLP-ADT is configured with account information. 

FAST BLINK – Download session with Compass in progress. 

YELLOW MESSAGE 

 

ON 

– Message transmission pending. 

QUICK PERIODIC BLINK - Normal 

FAST BLINK – Message waiting for network ACK. 

RED FAULT 

ON 

– No contact with network. 

OFF– Normal. 

SLOW BLINK – Loss of communication with the panel (ECP fault). 

FAST BLINK – No network contact AND loss of communication with the panel. 

GREEN MINIMUM 

SIGNAL 
STRENGTH 

ON – Minimum required signal strength is present. 

BLINKING – Marginal signal strength is present. 

OFF– Installation is not recommended. 

ALL (of the above) 

FAST BLINK – Hardware Error. Call the ADT Technical Assistance Center. 

 

Содержание GSMVLP-ADT

























Отзывы: