ADLINK Technology NuPRO-598 Series Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 90

ADLINK Technology NuPRO-598 Series Скачать руководство пользователя страница 64

56

•

BIOS Configuration

Integrated Peripherals

This o ption sets your hard disk configuration, mode and port.

ROM PCI/ISA BIOS

INTEGRATED PERIPHERALSP

AWARD SOFTWARE INC.

IDE HDD Block Mode

: Enabled

Onboard Parallel Port

: 378/IRQ7

IDE Primary Master PIO

: Auto

Parallel Port Mode

: SPP

IDE Primary Slave PIO

: Auto

ECP Mode Use DMA

: 1

IDE Primary Master UDMA

: Auto

EPP Mode Select

: EPP1.9

IDE Primary Slave UDMA

: Auto

On-Chip Primary PCI IDE

: Enabled

USB Keyboard Support

: Disabled

Onboard Lan Chip

: Enabled

Onboard VGA Chip

: Enabled

KBC input clock

: 6 MHz

Onboard FDC Controller

: Enabled

Onboard Serial Port 1

: 3F8/IRQ4

Onboard Serial Port 2

: 2F8/IRQ3

ESC : Quit

á

â

ß

: Select Item

UART Mode Select

: Normal

F1 : Help

PU/PD/+/- : Modify

UART2 Duplex Mode

: Full

F5 : Old Values

(Shift) F2 : Color

RxD , TxD Active

: Hi , Hi

F6 : Load BIOS Defaults

IR Transmission delay

: Disabled

F7 : Load Setup Defaults

IDE HDD Block Mode

This field allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive.

Enabled<Default>

IDE controller uses block mode

Disabled

IDE controller uses standard mode

IDE Primary Master/Slave PIO

These fields allow your system hard disk controller to work faster. Rather
than have the BIOS issue a series of commands that transfer to or from the
disk drive, PIO (Programmed Input/Output) allows the BIOS to
communicate with the controller and CPU directly.

The system supports five modes, numbered from 0 (default) to 4, which
primarily differ in timing. When Auto is selected, the BIOS will select the
best available mode.

Auto<Default>

Auto select which mode that BIOS
communicates with the controller and CPU

Mode0~Mode4

User define the PIO mode

«
...
62
63
64
65
66
...
»

Содержание NuPRO-598 Series



























































































Отзывы:

Нет отзывов