ADInstruments PowerLab 2/20 Скачать руководство пользователя

Страница: 36 / 54

PowerLab Owner’s Guide

The computer refuses to boot with the PowerLab connected, or the
computer can’t find the PowerLab

The PowerLab is off or the power is switched off at the wall, the
power cable is not connected firmly, or a fuse has blown.

•

Check switches, power connections, and fuses.

A poor connection between PowerLab and computer, or bad cable.

•

Ensure that the cable is firmly attached at both ends and try
again. If there is still a problem, try a new cable.

The PowerLab has an internal problem or has ‘hung’.

•

Turn everything off, and then after at least five seconds turn the
PowerLab back on again. Turn on the computer and try using the
software again.

The connected computer does not properly support USB.

•

USB needs a Power Macintosh with Mac OS 8.5 or later; it simply
will not work with earlier hardware, such as a 68K Macintosh, or
earlier operating systems, such as System 7.

The computer hangs up while recording, or there is data loss

A poor connection between PowerLab and computer, or bad cable.

•

Ensure that the cable is firmly attached at both ends and try
again. If there is still a problem, try a new cable.

The PowerLab doesn’t work or the program crashes after a short time

A poor connection between PowerLab and computer, or bad cable.

•

Ensure that the cable is firmly attached at both ends and try
again. If there is still a problem, try a new cable.

Содержание PowerLab 2/20























































Результаты поиска

Содержание PowerLab 2/20

Отзывы:

Похожие инструкции для PowerLab 2/20

Бренды по названию

Популярные бренды

ADInstruments PowerLab 2/20, Руководство пользователя

Результаты поиска

Содержание PowerLab 2/20

Отзывы:

Похожие инструкции для PowerLab 2/20

Бренды по названию

Популярные бренды