ADInstruments PowerLab 2/20 Скачать руководство пользователя | Manualshive

Страница: 54 / 54

background image

46

PowerLab Owner’s Guide

Hardware Warranty

ADI warrants that the hardware purchased by the
Purchaser shall be free of defects in material and
workmanship for one year from its date of
purchase. If there is such a defect, ADI will repair
or replace the equipment as appropriate, and the
duration of the warranty shall be extended by the
length of time needed for repair or replacement.

To obtain service under this warranty, the
Purchaser must notify ADI of the defect before the
warranty expires. Unless other arrangements are
made, ADI will provide an RMA (Return
Merchandise Authority) number, and a service
centre address to which the Purchaser must ship
the defective product at his or her own expense.
The product should be packed safely (preferably in
its original packaging) and have the RMA number
on the shipping label, beneath the address. ADI
will pay return shipping.

This warranty applies only to hardware used
normally and within its operating specifications. It
does not cover hardware modified in any way,
subjected to unusual physical, electrical, or
environmental stress, used with incorrectly wired
or substandard connectors or cables, or with the
original identification marks altered.

Software License

The Purchaser has the non-exclusive right to use
the supplied ADI software. (The Purchaser’s
employees or students, for instance, are entitled to
use it, provided they adhere to this Agreement.)

The Purchaser can make as many backup copies of
ADI software as is reasonable. Each separate
purchase of a software program, however, licenses
it to be used on only one computer at any given
time. Although multiple copies of a purchased
program may exist, two or more copies must not
be used simultaneously. Site licenses (multiple-
user licenses) are treated as if five copies of a
program were purchased separately, even if only
one CD or set of disks is provided.

Technical Support

Once a customer registration form has been filled
out and sent in, the Purchaser is entitled to free
technical support for any ADI product for one year
from its date of purchase. (A customer registration
form should be included with each product: if for
some reason you cannot find one, contact ADI for
another.) This involves help and advice concerning
installation, operation, particular uses, and
problems with ADI products. Services not directly
related to ADI products may incur a charge.

Jurisdiction

This Agreement shall be governed by the laws of
New South Wales in Australia, and any
proceedings concerning it shall be heard and
resolved by the Supreme Court of New South
Wales in Australia.

«
...
52
53
54

Содержание PowerLab 2/20























































Отзывы:

Нет отзывов

Похожие инструкции для PowerLab 2/20

Бренд: T&D Страницы: 2

DIGITAL VOICE RECORDER WS-200S

Бренд: Olympus Страницы: 2

Бренд: Spycentre Security Страницы: 8

Бренд: Laboratory2 Страницы: 19

Бренд: Daping Страницы: 20

Бренд: Tascam Страницы: 36

Бренд: JiGMO Страницы: 45

Бренд: Laboratory2 Страницы: 18

Бренд: Olympus Страницы: 45

Бренд: yemenren Страницы: 11

POVCAM AG-MDR25P

Бренд: Panasonic Страницы: 261

Бренд: aTTo Digital Страницы: 6

Бренд: aTTo Digital Страницы: 7

Бренд: aTTo Digital Страницы: 7

Бренд: aTTo Digital Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды