ADInstruments PowerLab 2/20 Скачать руководство пользователя | Manualshive

Страница: 16 / 54

background image

8

PowerLab Owner’s Guide

The Back Panel

The PowerLab back panel provides the sockets to connect the
PowerLab to the computer, front-ends, the power outlet, and so on.
This section describes each of the back panel features. The back
panels are the same for the PowerLab 2/20 and PowerLab 4/20.

I

2

C Output

The I

2

C output is a special port designed to connect to front-ends

made by ADInstruments. It supplies power and communications. A
PowerLab can have as many front-ends connected to it as it has
appropriate connectors. All of them connect to this port in a simple
daisy-chain arrangement.

Note

. You should not attempt to run other

external devices from the I

2

C port: it is designed for use only with

ADInstruments front-ends. Only 50 mA maximum current can be
provided through this bus, so it should not be used for third-party
devices drawing more current.

USB Port

The PowerLab connects to your computer using a USB (universal
serial bus) port. This works with USB 1.1-compliant computers with
USB connectors or a PCI USB card. To operate, USB needs a Power
Macintosh running Mac OS 8.5 or later, or a PC running Windows 98
or 2000 or later.

No user serviceable parts inside.
Refer servicing to qualified service personnel.

Serial

Port

2

I C Bus

Rated Voltage:
90-260 V AC 50/60 Hz 20 VA

Made in Australia by ADInstruments Pty Ltd.

Not intended for human connection
unless connections marked appropriately.

Power switch

Earth

I

2

C

connector

USB
connector

Model and serial numbers

Device rating
information

Power socket

Serial
connector

Figure 1–3

The back panel of the
PowerLab 2/20 and
PowerLab 4/20.

«
...
14
15
16
17
18
...
»

Содержание PowerLab 2/20























































Отзывы:

Нет отзывов

Похожие инструкции для PowerLab 2/20

Бренд: Olympus Страницы: 57

Бренд: Vidicode Страницы: 102

Бренд: NanoEnTek Страницы: 7

Бренд: Hitachi Страницы: 62

Бренд: Hitachi Страницы: 72

Бренд: Hitachi Страницы: 91

Бренд: Hitachi Страницы: 76

Бренд: Hitachi Страницы: 71

Бренд: Hitachi Страницы: 95

Бренд: Hitachi Страницы: 93

Бренд: Hitachi Страницы: 120

Бренд: Hitachi Страницы: 4

VoiceTracer DVT2050

Бренд: Philips Страницы: 2

VoiceTracer VTR9100

Бренд: Philips Страницы: 36

VoiceTracer VTR5166

Бренд: Philips Страницы: 38

Бренд: Philips Страницы: 51

Бренд: Philips Страницы: 51

Бренд: Philips Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды