ADB F-Range L-850C Скачать руководство пользователя страница 48

Страница: 48 / 60

F-Range Type L-850C Style 3 Inset Lights

Repair



2006 ADB Airfield Solutions, Incorporated

96A0285D

Page 6-15

Issued 04/13

See Figure 6-12. Remove both screws (F7) and the wire

clamp (F6).

NOTE:

Replace the wire grommets (F5) when damaged or aged.

Figure 6-12 L-823 Cordset

See Figure 6-5. Unplug the fast-on connectors (7) from the cable

assembly.

See Figure 6-12. Pull the cordset cable assembly (F9) out of the

inner cover and discard the wire grommets (F5).

Bring the new cable assembly (F9) through the wire clamp (F6).

Put a new wire grommet (F5) on each of the wires, taking care of

the direction. Put the smaller diameter into the inner cover

recesses.

Install the wires in the inner cover.

Reinstall the wire clamp (F6) by means of both cross recessed

countersunk screws (F7).

NOTE:

Do not torque down the screws entirely at this step.

10.

Remove the insulation of the wires over about 5 mm.

11.

Crimp on the new fast-on connectors and connect them to the

terminals. Adjust the wires inside the inner cover.

12.

Torque the screws (F7) to 31



4 inch-pounds (3.5



0.5 Nt-m).

7. Replacing L-823 Cordset

(contd.)

Содержание F-Range L-850C





























































Результаты поиска

Содержание F-Range L-850C

Отзывы:

Похожие инструкции для F-Range L-850C

Бренды по названию

Популярные бренды

ADB F-Range L-850C, Руководство пользователя

Результаты поиска

Содержание F-Range L-850C

Отзывы:

Похожие инструкции для F-Range L-850C

Бренды по названию

Популярные бренды