ADB F-Range L-850C Скачать руководство пользователя страница 46

Страница: 46 / 60

F-Range Type L-850C Style 3 Inset Lights

Repair



2006 ADB Airfield Solutions, Incorporated

96A0285D

Page 6-13

Issued 04/13

Remove the prism-keeper plate (B5) and the flat seal (B4).

Push the prism (B3) with the sock seal (B2) towards the inside of

the cover.

Clean and degrease the prism chamber with any effective

solvent.

Never use any abrasive substance. This will scratch or frost

the prism.

Apply a thin layer of lubricant MOLYKOTE (67A0095) BG87
INERTA or MOLYKOTE (67A0095) BG88 INERTA in the prism

chamber using a small brush.

Install a new sock seal (B2) over the prism (B3).

Push the prism/gasket assembly in the prism pocket from the

inside and clean the inner surface of the prism.

Install a new flat seal (B4) over the prism-keeper plate (B5).

Reinstall hardware with the Phillips pan head screws (B7). Apply

a droplet of sealant Loctite 270 to the last threads. Torque to 3.5



0.5 Nt-m (31



4 inch-pounds).

Refer to Table 6-1 in

Replacing Lamp and Filter

in this section for

parts referred to in Figure 6-4.

To replace the optical unit, perform the following procedure:

Remove the lamp(s). Refer to

Replacing Lamp and Filter

in this

section.

See Figure 6-4. Remove the optical unit (1) by loosening

screws (5).

Position the new optical unit with new grommets (4).

NOTE:

See Figure 2-3. Lamps and lamp holders must be

assembled to the same side of the optical bracket labeled “THIS

SIDE UP”.

Torque the fixing screws to 3.5



0.5 Nt-m (31



4 inch-pounds).

5. Replacing Prism

(contd.)

Replacing Optical Unit

Содержание F-Range L-850C





























































Результаты поиска

Содержание F-Range L-850C

Отзывы:

Похожие инструкции для F-Range L-850C

Бренды по названию

Популярные бренды

ADB F-Range L-850C, Руководство пользователя

Результаты поиска

Содержание F-Range L-850C

Отзывы:

Похожие инструкции для F-Range L-850C

Бренды по названию

Популярные бренды