Adaptec ARO-1130CA Скачать руководство пользователя страница 68

C-2

ARO-1130CA Installation and Hardware Guide

Sample command lines for 

config.sys 

file:

device=c:\scsi\aspi8dos.sys /d
device=c:\scsi\aspicd.sys /d:aspicd0

sample command line for 

autoexec.bat 

file:

\dos\mscdex.exe /d:aspicd0 /M:12

(This assigns the CD-ROM the next available drive letter, typi-
cally D if there is only one DOS drive.)

The following tables describe the 

aspi8dos

 and 

aspicd

 command 

line options. For a description of 

mscdex

 command line options, see 

your Microsoft DOS documentation. You can type command line 
options in uppercase or lowercase letters. Leave a blank space 
between options.

Command Line Options for 

aspi8dos.sys

Option

Example

Use

/ccbs

<count>

/ccbs8

Specifies the maximum number of concurrent ASPI com-
mands that can be supported. The valid range is 1 through 
16. The default is 4. If you increase this value, the size of the 
ASPI manager also increases. Use this option only if you 
want to run an ASPI program that specifies a higher number 
of concurrent commands.

/d

/d

Displays information about the ARO-1130CA and attached 
SCSI devices when the computer boots.

/L

/L

Enables 

aspi8dos to recognize all eight possible LUNs asso-

ciated with each SCSI ID. If the option is not used, 

aspi8dos 

can recognize only LUN 0 for each SCSI ID.

/m

n

/m1

Causes aspi8dos to scan the PCI bus. The method used to 
scan the bus is determined by the value of 

n:

/mb = scan PCI bus using PCI BIOS calls
/m1 = scan PCI bus using Mechanism #1
/m2 = scan PCI bus using Mechanism #2

aspi8dos automatically scans the PCI bus for SCSI devices. 
It tries to determine which scanning method will work best 
for the given system configuration. Use the /mb, /m1, and 
/m2 options only if you want to override the 

aspi8dos inter-

nal scanning mechanism. Usually 

aspi8dos can determine 

which scanning method is optimal for your system. (PCI 
BIOS calls are described in the PCI BIOS spec; scanning 
mechanisms #1 and #2 are described in the PCI spec.

Содержание ARO-1130CA















































































Отзывы: