Adaptec ARO-1130CA Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 78

Adaptec ARO-1130CA Скачать руководство пользователя страница 11

1-1

1

▼ ▼ ▼ ▼

Introduction

The Adaptec

®

ARO

™

-1130CA RAIDport II

™

Card provides power-

ful disk array support in personal workstations with RAIDport II
on-board.

This Installation and Hardware Guide explains how to install the
ARO-1130CA, create the first array, and then install the supporting
software. The Adaptec Array1000CA Family Array Management Guide,
which is included with the ARO-1130CA, explains how to use the
software to create and manage additional arrays.

System Requirements

The minimum system requirements for the ARO-1130CA are

■

A RAIDport II on-board system with an available
PCI/RAIDport II slot

■

A minimum of one SCSI hard disk drive

■

A standard 168-pin, 16-, 32-, or 64-MByte, EDO 3.3v, 60ns or
faster DIMM installed on the card. (See the Adaptec Web Site
at

http://www.adaptec.com/RAID

for a list of approved DIMMs

and vendors.)

■

Five MBytes of free hard disk space for the ARO-1130CA soft-
ware (five MBytes of free hard disk space on the Windows sys-
tem disk are also required for the temporary files created
during installation of the software)

■

Windows NT

™

Workstation 4.0 or higher

■

A 3.5-inch 1.44-MByte primary (boot) floppy disk drive

«
...
9
10
11
12
13
...
»

Содержание ARO-1130CA















































































Отзывы:

Нет отзывов