Adaptec ARO-1130CA Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 78

Adaptec ARO-1130CA Скачать руководство пользователя страница 50

5-6

ARO-1130CA Installation and Hardware Guide

SCSI Device Configuration

The SCSI device settings allow you to configure certain parameters
for each device on the SCSI bus. To configure settings for a specific
device, you must know the SCSI ID assigned to that device. If you are
not sure of the SCSI ID, see Using the SCSI Disk Utilities on page 5-4.

■

Initiate Sync Negotiation

—This option determines whether

synchronous data transfer negotiation (Sync Negotiation)
between the device and ARO-1130CA is initiated by the SCSI
channel controlled by the ARO-1130CA. Normally, you should
leave Initiate Sync Negotiation set to enabled, because most
SCSI devices support synchronous negotiation and because it
allows for faster data transfer. The default setting is Yes.

■

Maximum Transfer Rate

—This option determines the maxi-

mum data transfer rate that the SCSI channel controlled by the
ARO-1130CA supports. The default setting is 20.0 MBytes/sec
(10 MBytes/sec for motherboards that do not support Wide
SCSI). (The effective data transfer rate is doubled when Initiate
Wide Negotiation is set to Yes. For example, a transfer rate of
20 MBytes/sec becomes 40 MBytes/sec.)

■

Enable Disconnection

—This option determines whether the

SCSI channel controlled by the ARO-1130CA allows the SCSI
device to disconnect from the SCSI bus (sometimes called
Disconnect/Reconnect). The default setting is Yes.

You should leave Enable Disconnection set to Yes if two or
more SCSI devices are supported by the ARO-1130CA. If only
one SCSI device is supported by the ARO-1130CA, you can set
Enable Disconnection to No to achieve slightly better perfor-
mance.

■

Initiate Wide Negotiation

—This option determines whether

the SCSI channel controlled by the ARO-1130CA attempts
16-bit data transfer instead of 8-bit data transfer. The default
setting is Yes. (The effective data transfer rate is doubled when
16-bit data transfer is used. For example, a transfer rate of
10 MBytes/sec becomes 20 MBytes/sec.)

«
...
48
49
50
51
52
...
»

Содержание ARO-1130CA















































































Отзывы:

Нет отзывов