background image

 

 

 

Adam Equipment Company 2012

 

 

 

Manufacturer’s Declaration of Conformity 

This product has been manufactured in accordance with the harmonised European standards, following the 

provisions of the below stated directives: 

Restriction of the use of certain hazardous substances 

in electrical and electronic equipment 2011/65/EC (RoSH) 

 

Electro Magnetic Compatibility Directive 2004/108/EC 

Low Voltage Directive 2006/95/EC  

Adam Equipment Co. Ltd. 

Maidstone Road,  Kingston 

Milton Keynes, MK10 0BD 

United Kingdom 

 

FCC COMPLIANCE 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to 

Part  15  of  the  FCC  Rules.    These  limits  are  designed  to  provide  reasonable  protection  against  harmful 

interference when the equipment is operated in a commercial environment.  The equipment generates, uses, 

and  can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the  instruction 

manual,  may  cause  harmful  interference  to  radio  communications.    Operation  of  this  equipment  in  a 

residential area is likely to cause harmful interference in  which case the user  will be required to correct the 

interference at his own expense. 

Shielded interconnect cables must be employed with this equipment to insure compliance with the pertinent 

RF emission limits governing this device. 

Changes or modifications not expressly approved by Adam Equipment could void the user's authority to 

operate the equipment

 

WEEE

 

COMPLIANCE 

 

Any Electrical or Electronic Equipment (EEE) component or assembly of parts intended to be incorporated into 

EEE devices as defined by European Directive 2002/95/EEC must be recycled or disposed using techniques that 

do  not  introduce  hazardous  substances  harmful  to  our  health  or  the  environment  as  listed  in  Directive 

2002/95/EC  or  amending  legislation.    Battery  disposal  in  Landfill  Sites  is  more  regulated  since  July  2002  by 

regulation  9  of  the  Landfill  (England  and  Wales)  Regulations  2002  and  Hazardous  Waste  Regulations  2005. 

Battery recycling has become topical and the Waste Electrical and Electronic Equipment (WEEE) Regulations 

are set to impose targets for recycling. 

Содержание NCSA 20plus





















Отзывы: