background image

 

15 

Adam Equipment Company 2012 

WARRANTY INFORMATION

 

Adam Equipment offers Limited Warranty (Parts and Labour) for the components failed due to defects 

in materials or workmanship.  Warranty starts from the date of delivery. 

During the warranty period, should any repairs be necessary, the purchaser must inform its supplier or 

Adam  Equipment  Company.  The  company  or  its  authorised  Technician  reserves  the  right  to  repair  or 

replace the components at any of its workshops depending on the severity of the problems. However, 

any  freight  involved  in  sending  the  faulty  units  or  parts  to  the  service  centre  should  be  borne  by  the 

purchaser. 

The warranty will cease to operate if the equipment is not returned in the original packaging and with 

correct  documentation  for  a  claim  to  be  processed.  All  claims  are  at  the  sole  discretion  of  Adam 

Equipment. 

This  warranty  does  not  cover  equipment  where  defects  or  poor  performance  is  due  to  misuse, 

accidental  damage,  exposure  to  radioactive  or  corrosive  materials,  negligence,  faulty  installation, 

unauthorised  modifications  or  attempted  repair  or  failure  to  observe  the  requirements  and 

recommendations  as  given  in  this  User  Manual.  Additionally  rechargeable  batteries  (where  supplied) 

are not covered under warranty. 

Repairs  carried  out  under  the  warranty  does  not  extend  the  warranty  period.  Components  removed 

during the warranty repairs become the company property. 

The  statutory  right  of  the  purchaser  is  not  affected  by  this  warranty.  The  terms  of  this  warranty  is 

governed by the UK law. For complete details on Warranty Information, see the terms and conditions 

of sale available on our web-site. 

Содержание NCSA 20plus





















Отзывы: