Page 22
1
1
2
2
3
4
3
5
6
4
7
8
5
1
2
6
REC
OSD
MAIN
REC
1
7
8
REC
2
3
4
L
R
LS
RS
SUB
C
L
R
L
R
L
R
L
R
OUT
AUDIO OUTPUTS
AUDIO INPUTS
VIDEO INPUTS
VIDEO OUT
S-VIDEO OUT
1
2
3
4
DIGITAL AUDIO INPUTS
S-VIDEO INPUTS
LOW VOLTAGE
AC INPUT
115V-60Hz/230V-50Hz
AC OUTPUT
10A Max Switched
ADA Bus™
1 2 3 4
DATA PORT
Serial Data
12VDC OUT
100mA Max Per
DC 1
1- 2+
DC 2
1- 2+
HDTV/RGB
COMPONENT
VIDEO
SWITCHER
Use With DVD
Players or
Digital Video
Tape Players
1
2
OUT
Y
Cr
Cb
LASER DISC PLAYER
Dolby Digital (AC-3)
RF Switcher & AC-3
RF Demodulator
1
2
Connections!
In order to play an AC-3 Laser
Disc, you must connect the Digital
AC-3 Output to a Digital Audio
Input (RCA Type Coax) below.
DC Input Mute Switch
OFF
ON
CAUTION: Disconnect Supply Cord Before Servicing.
ATTENTION: Debrancher Avant Le Depannage.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION!
RISQUE DE CHOC ELECTRIQUE.
NE PAS OUVRIR
MADE IN U.S.A.
WARNING! Risk Of Hazardous Energy!
Make Proper Connections.
AVERTISSEMENT! Energie Electrique Dangereuse!
Faire Des Connexions Propres Pour L'Hautparleur.
Voir La Notice De Fonctionnement.
Use Same
Value Fuse
115V-1AS.B.
230V-.5AS.B.
Voltage
Selector &
Safety Fuse
On This Side
115 V
115V
230V
15
Manufactured under license from Dolby Laboratories Licensing Corp.
"Dolby", "Dolby Digital", "Pro Logic", & the Double-D Symbol are the trademarks of Dolby Laboratories Licensing Corp.
Manufactured under license from DTS Technology, LLC. DTS Digital Surround is a trademark of DTS Technology LLC.
Manufactured under license from Lucasfilm Ltd. U.S. patent numbers 5,043,970; 5,189,703; and 5,222,059.
Foreign patents pending. Lucasfilm and THX are registered trademarks of Lucasfilm Ltd.,
Cinema Reference
1
2
3
OPTICAL INPUTS
In order to play an AC-3 Laser Disc,
you must connect the Digital AC-3
Output to a Digital Audio Input.
Laser Disc without Digital Audio Output
(May have AC-3 RF Output)
Stereo
Audio Out
R
L
Video
Out
RF • AC-3
Out (LD)
Laser Disc AC-3 Loop Cable
(You must connect this cable to play
Dolby Digital (AC-3) Laser Discs.)
AC-3 RF Cable
(Connect this cable if
laser disc has an AC-3
RF output.)
Video
Cable
Stereo AudioCable
(This cable carries standard 2 channel
analog audio from CDs & Laser Discs.)
2
2
2L
2R
4
Changing the Cinema Reference’s Audio Input to Accommodate A Second Laser Disc
If you are using a laser disc player which only has either a digital coax audio output or an optical digital
audio output, you will need to use either a 75
Ω
coax to connect it to Digital Input #3 or an optical TOS-
Link type cable to connect the laser disc to Optical #3 on the Cinema Reference. Then follow these
steps.
1
Turn the Input knob to LASERDISC 2 and press the knob.
2
Turn the Mode knob clockwise to SETUP MODE and press the knob.
3
Turn the Mode knob to AUDIO INPUT and press the knob. Once the knob is pressed the will
read “ANALOG IN 1”.
4
Turn the mode knob until the display reads either DIGITAL IN 2 or OPTICAL IN 2 (based on
your configuration) and press the knob.
You have now altered the LASERDISC 2 input to access either Digital Input 2 or Optical Input 2.
Connection 3
Connection 4
Connection 2
Connection 1
