SERIES IP503 INDUSTRIAL I/O PACK EIA/TIA-232E & CENTRONICS COMMUNICATION MODULE
___________________________________________________________________________________________
- 22 -
CABLE: MODEL 5029-900
Type: Model 5029-900 APC8600 High-Density Cable: A 36-inch
long interface cable that mates the high-density (25mil pitch)
50-pin I/O connectors of the APC8600 PC/AT ISAbus carrier
board, to the high density connectors on the APC8600
Termination Panels (described below)
Application: Used with the APC8600 PC carrier and termination
panel. It mates the high-density (25mil pitch) 50-pin I/O
connectors of the APC8600 PC/AT ISAbus carrier board, to
the high density connectors on the APC8600 Termination
Panel (described below)
Length: 36-inches
Cable:50-wire flat ribbon cable, 28 gage, Non-Shielded,
T&B/Ansley Part 135-050 or equivalent
Headers:50-pin, high-density, 25-mil pitch, female header.
Header- T&B Ansley Part 311-050302 or equivalent
Keying: Headers at both ends have polarizing key to prevent
improper installation
Shipping Weight:10 pound (05Kg) packaged
TERMINATION PANEL:MODEL 5025-552
Type: Termination Panel For AVME9630/9660 Boards
Application: To connect field I/O signals to the Industrial I/O
Pack (IP)
Termination Panel: Acromag Part 4001-
040(Phoenix Contact Type FLKM 50)The 5025-552
termination panel facilitates the connection of up to 50 field
I/O signals and connects to the AVME9630/9660 3U/6U non-
intelligent carrier boards (A-D connectors only) via a flat
ribbon cable (Model 5025-550-x or 5025-551-x)The A-D
connectors on the carrier board connect the field I/O signals
to the P2 connector on each of the Industrial I/O Pack
modules. Field signals are accessed via screw terminal
strips. The terminal strip markings on the termination panel
(1-50) correspond to P2 (pins 1-50) on the Industrial I/O Pack
(IP)Each Industrial I/O Pack (IP) has its own unique P2 pin
assignments. Refer to the IP module manual for correct
wiring connections to the termination panel
Schematic and Physical Attributes: See Drawing 4501-464
Field Wiring:50-position terminal blocks with screw clamps. Wire
range 12 to 26 AWG
Connections to AVME9630/9660:P1, 50-pin male header with
strain relief ejectors. Use Acromag 5025-550-x or 5025-551-
x cable to connect panel to VME board Keep cable as short
as possible to reduce noise and power loss
Mounting: Termination panel is snapped on the DIN mounting
rail
Printed Circuit Board: Military grade FR-4 epoxy glass circuit
board, 0063 inches thick
Operating Temperature:-15
°
C to +50
°
C
Storage Temperature:-15
°
C to +50
°
C
Shipping Weight
:125 pounds (06kg) packaged
TERMINATION PANEL:MODEL 5029-910
Type: Screw-Terminal Termination Panel For Acromag APC8600
PC/AT ISAbus Carrier Boards
Application: This panel converts the high-density ribbon-cable
connectors coming from the APC8600 carrier board
(Acromag cable Model 5029-900) to screw terminals, for
direct-wired interfaces. This panel facilitates the connection
of up to 50 field I/O signals and connects to the APC8600
PC/AT ISAbus carrier board via high-density (25-mil pitch) flat
ribbon cable and connectors (see cable Model 5029-900)The
A & B connectors on the carrier board connect the field I/O
signals to the P2 connector on each of the Industrial I/O Pack
modules. FieLd signals are accessed via screw terminal
strips. Each Industrial I/O Pack (IP) has its own unique P2
pin assignments. Refer to the IP module manual for correct
wiring connections to the termination panel
Field Wiring:50-position terminal blocks with screw clamps. Wire
range 12 to 26 AWG
Connections to APC8600:P1, 50-pin, high-density male header
with strain relief
Mounting: Termination Panel includes mounting holes
Printed Circuit Board: MilItary grade FR-4 epoxy glass circuit
board, 0063 inches thick
Operating Temperature:-40
°
C to +85
°
C
Storage Temperature:-55
°
C to +125
°
C
Shipping Weight
:125 pounds (06kg) packaged
TRANSITION MODULE: MODEL TRANS-GP
Type: Transition module for AVME9630/9660 boards
Application: To repeat field I/O signals of IP modules A through
D for rear exit from VME card cages. This module is
available for use in card cages which provide rear exit for I/O
connections via transition modules (transition modules can
only be used in card cages specifically designed for them)It is
a double-height (6U), single-slot module with front panel
hardware adhering to the VMEbus mechanical dimensions,
except for shorter printed circuit board depth. Connects to
Acromag termination panel 5025-552 from the rear of the
card cage, and to AVME9630/9660 boards within card cage,
via flat 50-pin ribbon cable (cable Model 5025-550-X or 5025-
551-X)
Schematic and Physical Attributes: See Drawing 4501-465
Field Wiring:100-pin header (male) connectors (3M 3433-D303 or
equivalent) employing long ejector latches and 30 micron
gold in the mating area (per MIL-G-45204, Type II, Grade
C)Connects to Acromag termination panel 5025-552 from the
rear of the card cage via flat 50-pin ribbon cable (cable Model
5025-550-X or 5025-551-X)
Connections to AVME9630/9660: 50-pin header (male)
connectors (3M 3433-1302 or equivalent) employing long
ejector latches and 30 micron gold in the mating area (per
MIL-G-45204, Type II, Grade C)Connects to AVME9630/9660
boards within the card cage via flat 50-pin ribbon cable (cable
Model 5025-550-X or 5025-551-X)
Mounting: Transition module is inserted into a 6U-size, single-
width slot at the rear of the VMEbus card cage
Printed Circuit Board: Six-layer, military-grade FR-4 epoxy glass
circuit board, 0063 inches thick
Operating Temperature:-40
°
C to +85
°
C
Storage Temperature:-55
°
C to +105
°
C
Shipping Weight:125 pounds (06Kg) packaged
