Acces I/O products E-RDAG12-8 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 38

Acces I/O products E-RDAG12-8 Скачать руководство пользователя страница 7

RDAG12-8 Manual

Analog Outputs

These units consist of eight independent 12-bit digital-to-analog converters (DACs), and amplifiers
for voltage outputs and voltage-to-current conversion.  The DACs may be updated in a channel-by-
channel  mode  or  simultaneously.    There  are  eight  channels  of  voltage  output  and  eight
complimentary channels for 4-20mA current output sinks.  The output voltage ranges are software
selectable.  Calibration is  performed  by software.  Factory calibration constants  are  stored  in  the
EEPROM memory and can be updated by disconnecting the I/O wiring and entering the software
calibration mode.  Model RDAG12-8 can supply analog outputs of up to 5 mA on voltage ranges of
0-5V,  ±5V,  and  0-10V.    By  writing discrete  values of  a  desired  waveform into  the buffers and
loading  the  buffers  into  the  DAC  at  a  programmable  rate  (31-6,000Hz)  the  units  can  generate
arbitrary waveforms or control signals.

Model RDAG12-8H is similar except that each DAC output can drive loads up to 250mA using a
±12V @ 2.5A local power supply.

Digital I/O

Both models also have seven digital input/output ports. Each port can be individually programmed
as an input or an output.  Digital input ports can accept logic high input voltages up to 50V and are
overvoltage protected to 200 VDC.  Output drivers are open collector and can comply with up to 50
VDC of user-supplied voltage.  Each output port can sink up to 350 mA but total sink current is
limited to a cumulative total of 650 mA for all seven bits.

Watchdog Timer

The built-in watchdog timer resets the Pod if the microcontroller "hangs up" or the power supply
voltage drops below 7.5 VDC. The microcontroller may also be reset by an external manual
pushbutton connected to /PBRST (pin 41 of the interface connector).

Page 1-2

Manual MRDAG12-8H.Bc2

«
...
5
6
7
8
9
...
»

Содержание E-RDAG12-8







































Отзывы:

Нет отзывов