Acces I/O products E-RDAG12-8 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 38

Acces I/O products E-RDAG12-8 Скачать руководство пользователя страница 29

RDAG12-8 Manual

Hello Message

H*

Hello message

Any string of characters starting with "H" will be interpreted as this command. ("H[CR]" alone is
also acceptable.) The return from this command takes the form (without the quotes):

"=Pod aa, RDAG12-8 Rev rr Firmware Ver:x.xx ACCES I/O Products, Inc."

aa is the Pod address
rr is the hardware revision, such as "B1"
x.xx is the software revision, such as "1.00"

Example:

Read the greeting message.

SEND:

Hello?[CR]

RECEIVE:

Pod 00, RDAG12-8 Rev B1 Firmware Ver:1.00 ACCES I/O Products,
Inc.[CR]

Configure Baud Rate

(When Shipped by Acces, the Baud Rate Is Set at 9600.)

BAUD=nnn

Program the Pod with a new baud rate

This command sets the Pod to communicate at a new baud rate. The parameter passed, nnn, is
slightly unusual. Each n is the same digit from the following table:

Code

Baud Rate

0

1200

1

2400

2

4800

3

9600

4

14400

5

19200

6

28800

7

57600

Therefore, valid values for the command's "nnn" are 000, 111, 222, 333, 444, 555, 666, or 777.
The Pod returns a message indicating it will comply. The message is sent in the old baud rate, not
the new one. Once the message is transmitted, the Pod changes to the new baud rate. The new baud
rate is stored in EEPROM and will be used even after power-reset, until the next "BAUD=nnn"
command is issued.

Example:

Set the Pod to 19200 baud.

SEND:

BAUD=555[CR]

Page 3-8

Manual MRDAG12-8H.Bc2

«
...
27
28
29
30
31
...
»

Содержание E-RDAG12-8







































Отзывы:

Нет отзывов