Acces I/O products E-RDAG12-8 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 38

Acces I/O products E-RDAG12-8 Скачать руководство пользователя страница 18

RDAG12-8 Manual

Calibration

The setup software provided with the RDAG12-8 and RDAG12-8H supports the ability to check
calibration and to write correction values into EEPROM so they are available automatically on
power-up. Calibration checks need only be performed periodically, not every time power is cycled.
The SETUP.EXE software calibration procedure can be used to calibrate all three ranges and store
the values in the EEPROM. For Windows NT, you’ll need to boot to DOS to run this program. You
can create a DOS boot disk from any Windows system not running NT. We can provide a DOS boot
disk if necessary.

The SAMPLE1 program illustrates the procedure of recalling these values and adjusting the
readings. The description of the CALn? command shows the order in which the information is
stored in the EEPROM.

Installation

The RDAG12-8 and the RDAG12-8H enclosure is a non-sealed steel enclosure with a powder coated
finish. The enclosure measures 8" long by 5.32" wide by 2.2" high.

There are three jumper locations on the unit and their functions are as follows:

JP2, JP3, and JP4: Normally these jumpers should be in the "ISL" position. If you wish to

by-pass the opto-isolators, then you can move these jumpers to the "/ISL"
position.

Input/Output Pin Connections

Electrical connections to the RDAG12-8 are through cutouts in the ends of the enclosure.
Some versions of this product terminate in 2 DB25 connectors, see enclosure label for pinout.

Connector pin assignments for the 50-pin connector follow:

Page 2-6

Manual MRDAG12-8H.Bc2

«
...
16
17
18
19
20
...
»

Содержание E-RDAG12-8







































Отзывы:

Нет отзывов