manualshive.com logo in svg

Acces I/O products E-RDAG12-8, Руководство пользователя, Страница: 13 / 38

Поделиться
Скачать
Acces I/O products E-RDAG12-8 Скачать руководство пользователя страница 13

Chapter 2:  Installation 

The software provided with this card is contained on CD and must be installed onto your hard disk
prior to use.  To do this, perform the following steps applicable for your operating system. Substitute
the appropriate drive letter for your CD-ROM where you see  d: in the examples below.

CD Installation

WIN95/98/NT/2000

a.

Place the CD into your CD-ROM drive.

b.

The install program should automatically run after 30 seconds.  If the install program does

not run, click START | RUN and type d:install, click OK or press 

K

.

c.

Follow the on-screen prompts to install the software for this card.

Directories Created on the Hard Disk

The  installation  process  will  create  several  directories  on  your  hard  disk.    If  you  accept  the
installation defaults, the following structure will exist.

[CARDNAME]

Root  or  base  directory  containing  the  SETUP.EXE  setup  program  used  to  help  you  configure
jumpers and calibrate the card. 

DOS\PSAMPLES:

A subdirectory of  [CARDNAME] that contains Pascal samples.

DOS\CSAMPLES:

A subdirectory of [CARDNAME] that contains "C" samples.

Win32\language:

Subdirectories containing samples for Win95/98 and NT.

WinRISC.exe

A Windows dumb-terminal type communication program designed for RS422/485 operation. 
Used primarily with Remote Data Acquisition Pods and our RS422/485 serial communication
product line.  Can be used to say hello to an installed modem.  

ACCES32

This  directory  contains  the  Windows  95/98/NT  driver  used  to  provide  access  to  the  hardware
registers  when  writing  32-bit  Windows  software.    Several  samples  are  provided  in  a  variety  of
languages  to  demonstrate  how  to  use  this  driver.    The  DLL  provides  four  functions  (InPortB,
OutPortB, InPort, and OutPort) to access the hardware. 

This directory also contains the device driver for Windows NT, ACCESNT.SYS.  This device driver
provides register-level  hardware  access in  Windows  NT.  Two  methods of  using the driver  are
available,  through  ACCES32.DLL  (recommended)  and  through  the  DeviceIOControl  handles
provided by ACCESNT.SYS (slightly faster).

Page 2-1

Manual MRDAG12-8H.Bc2

Содержание E-RDAG12-8







































Отзывы:

Нет отзывов